Contact Us

STM32F207ZFT6

Brand: ST
ST STM32F207ZFT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F207ZFT6 — MCU & Embedded Processors | Superb Automation

STM32F207ZFT6

ST — MCU & Embedded Processors

Product Overview

The STM32F207ZFT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F207ZFT6: 768 Kbyte, LQFP144 body

STM32F207ZFT6 is a member of the STM32F205 and STM32F207 performance line described by DS6329 Rev 18. The order code fixes 768 Kbytes of Flash, 128 Kbytes of SRAM, the LQFP144 body at 20 x 20 mm with 144 pins, 114 general purpose I/O and 16 external channels on each of the 12 bit converters, and the core runs at up to 120 MHz from a 1.8 to 3.6 V supply.

Order code and memory

Order codeSTM32F207ZFT6
Program Flash768 Kbytes
SRAM128 Kbytes
PackageLQFP144, 20 x 20 mm, 144 pins
Maximum general purpose I/O114
Analog input channels16 external channels per converter
Digital to analog converternot present
External memory controllerfull flexible static memory controller with four chip selects
Supply voltage1.8 to 3.6 V
Maximum CPU clock120 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS6329 Rev 18

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 120 MHz with the adaptive real time accelerator, 1.25 DMIPS per MHz, 150 DMIPS, a memory protection unit and single cycle multiply and divide
Clock sources4 to 26 MHz high speed external crystal, 16 MHz factory trimmed internal RC, 32.768 kHz low speed internal and external sources, a main PLL and a separate audio PLL for the I2S blocks
Timerstwo advanced-control 16 bit timers with complementary outputs and dead time, four full featured general purpose timers of which TIM2 and TIM5 are 32 bit, six further general purpose 16 bit timers, two basic timers, the independent and window watchdogs, the SysTick counter and the RTC, which is the seventeen the cover counts
Serial interfacesthree SPI blocks two of which mux to I2S, three I2C blocks, four USARTs and two UARTs, two CAN 2.0B active controllers and one SDIO interface
DMAtwo DMA controllers with eight streams each and a FIFO per stream, sixteen streams in total, with circular buffer support
ADCthree 12 bit successive approximation converters with a 0.5 microsecond conversion time, each sharing up to 16 external channels, up to 24 channels across the three on the larger bodies and up to 6 Msps in triple interleaved mode
DACtwo 12 bit channels with output buffers
Ethernet10/100 MAC with dedicated DMA, MII or RMII, IEEE 1588 timestamping
Camera interfaceparallel camera interface, 8 to 14 bit, with its own DMA
Cryptographic accelerationnot present on this part
Programmable voltage detectorprogrammable voltage detector with selectable thresholds, plus power on reset, power down reset and brownout reset
Debug portserial wire debug and JTAG, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC, the 4 Kbytes of backup SRAM and the backup registers alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C and 1 kcycle at 105 C, with 30 years of retention at 85 C after one kcycle, 20 years at 55 C after 10 kcycles and 10 years at 105 C
Thermal resistance junction to ambient40 C/W on this package
Input tolerancealmost all inputs 5 V tolerant, with fast I/O toggling to 60 MHz on the larger bodies
USBone OTG full speed port on the device pins and one OTG high speed port that needs an external ULPI PHY
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The only difference between this part and STM32F207ZGT6 is the Flash size, 768 Kbytes against 1 Mbyte, and the price step between them is small enough that most boards take the larger one. This code is bought when the 1 Mbyte part is short and the firmware fits, which is a sourcing decision rather than a technical one, and the pinout makes the substitution safe on the board.

A firmware that fits in 768 Kbytes cannot hold two 512 Kbyte images, so the dual image field update pattern does not apply. The alternative on this density is a compressed image written into a reserved region, which needs about 400 Kbytes of source in the worst case and leaves little room. Equipment that must support field updates without a service visit usually specifies the 1 Mbyte code for this reason alone.

The SRAM is the full 112 plus 16 Kbytes, identical to the 1 Mbyte part. That is what makes this a genuine substitute in a network application, because the buffer count and the window size of the TCP stack depend on SRAM and not on Flash. A board that was validated on the larger part keeps its timing and memory behaviour when this one is fitted.

Ethernet, the camera interface, two CAN channels, three I2C blocks, four USARTs and two UARTs are all present, so the pin budget problem is the same as on the rest of the 144 pin range. The 114 pins are enough for RMII, a 16 bit memory bus, a 10 bit camera and three serial ports together, and not much more.

Thermal behaviour matches the rest of the package at 40 C/W, about 500 mW at 85 C ambient. Because the density is lower, code that ran from a larger Flash may in practice execute with more ART accelerator misses if the linker places hot functions differently, which shows up as a small current increase rather than a speed problem. The linker map is worth checking when substituting between densities.

Where this order code fits

It is the 768 Kbyte version of the 144 pin STM32F207, for boards that need everything the 1 Mbyte part offers but whose firmware fits with a quarter of the Flash to spare. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is this a drop in replacement for STM32F207ZGT6? Yes on the board, the package and the pinout. The only difference is 768 Kbytes instead of 1 Mbyte of Flash, so firmware that fits runs unchanged. The linker script has to be checked so that no region is placed above the 768 Kbyte boundary.

What does the F suffix change against the E and G codes? Flash only. E is 512 Kbytes, F is 768 Kbytes and G is 1 Mbyte. SRAM, peripherals, package and temperature grade are identical across the three.

Can a field update keep two images on 768 Kbytes? Not two full images of 512 Kbytes. On this density the usual approach is one compressed image in a reserved region or a smaller application footprint, which is why equipment with remote update needs usually specifies the 1 Mbyte code.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.