Contact Us

STM32F205ZFT6

Brand: ST
ST STM32F205ZFT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F205ZFT6 — MCU & Embedded Processors | Superb Automation

STM32F205ZFT6

ST — MCU & Embedded Processors

Product Overview

The STM32F205ZFT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F205ZFT6: 768 Kbyte, LQFP144 body

STM32F205ZFT6 is a member of the STM32F205 and STM32F207 performance line described by DS6329 Rev 18. The order code fixes 768 Kbytes of Flash, 128 Kbytes of SRAM, the LQFP144 body at 20 x 20 mm with 144 pins, 114 general purpose I/O and 16 external channels on each of the 12 bit converters, and the core runs at up to 120 MHz from a 1.8 to 3.6 V supply.

Order code and memory

Order codeSTM32F205ZFT6
Program Flash768 Kbytes
SRAM128 Kbytes
PackageLQFP144, 20 x 20 mm, 144 pins
Maximum general purpose I/O114
Analog input channels16 external channels per converter
Digital to analog converternot present
External memory controllerfull flexible static memory controller with four chip selects
Supply voltage1.8 to 3.6 V
Maximum CPU clock120 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS6329 Rev 18

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 120 MHz with the adaptive real time accelerator, 1.25 DMIPS per MHz, 150 DMIPS, a memory protection unit and single cycle multiply and divide
Clock sources4 to 26 MHz high speed external crystal, 16 MHz factory trimmed internal RC, 32.768 kHz low speed internal and external sources, a main PLL and a separate audio PLL for the I2S blocks
Timerstwo advanced-control 16 bit timers with complementary outputs and dead time, four full featured general purpose timers of which TIM2 and TIM5 are 32 bit, six further general purpose 16 bit timers, two basic timers, the independent and window watchdogs, the SysTick counter and the RTC, which is the seventeen the cover counts
Serial interfacesthree SPI blocks two of which mux to I2S, three I2C blocks, four USARTs and two UARTs, two CAN 2.0B active controllers and one SDIO interface
DMAtwo DMA controllers with eight streams each and a FIFO per stream, sixteen streams in total, with circular buffer support
ADCthree 12 bit successive approximation converters with a 0.5 microsecond conversion time, each sharing up to 16 external channels, up to 24 channels across the three on the larger bodies and up to 6 Msps in triple interleaved mode
DACtwo 12 bit channels with output buffers
Ethernetnot present, Ethernet is an STM32F207 feature
Camera interfacenot present on the STM32F205
Cryptographic accelerationnot present on this part
Programmable voltage detectorprogrammable voltage detector with selectable thresholds, plus power on reset, power down reset and brownout reset
Debug portserial wire debug and JTAG, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC, the 4 Kbytes of backup SRAM and the backup registers alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C and 1 kcycle at 105 C, with 30 years of retention at 85 C after one kcycle, 20 years at 55 C after 10 kcycles and 10 years at 105 C
Thermal resistance junction to ambient40 C/W on this package
Input tolerancealmost all inputs 5 V tolerant, with fast I/O toggling to 60 MHz on the larger bodies
USBone OTG full speed port on the device pins and one OTG high speed port that needs an external ULPI PHY
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The F in the order code is 768 Kbytes, which on this line carries the full SRAM column: 112 Kbytes of SRAM1 plus 16 Kbytes of SRAM2 and 4 Kbytes of backup SRAM. The 256 Kbyte part two steps down has 80 plus 16 Kbytes, so the memory step here is larger in working memory than the Flash figure alone suggests, and that is the number that decides the buffer count of a serial protocol stack.

This is a 144 pin body with 114 general purpose pins and no Ethernet. That combination is common on test equipment and industrial controllers where the network, when it exists at all, is a separate module on a serial port. The 10/100 MAC is only in the STM32F207 line, and boards that need it take STM32F207ZFT6, which is the same package, pinout and memory with the MAC and the camera interface added.

The memory controller is the full version here: four chip selects, separate address and data buses, NOR, PSRAM, SRAM, NAND and Compact Flash timing, with a timing register set per bank. A board that keeps its logs in a NAND and its run time data in a PSRAM uses two of the four chip selects and still has two spare, which is the practical argument for this package over the 100 pin body.

Seven hundred and sixty eight Kbytes of Flash is not enough for two 512 Kbyte images, so a field update on this density writes a compressed image into a reserved region rather than holding a full second copy. The size of the reserved region depends on how well the application compresses and has to be planned before the memory map is fixed; equipment that must keep a complete second image specifies the 1 Mbyte code.

The LQFP144 is rated 40 C/W, so at 85 C ambient the dissipation budget is about 500 mW. A board with a 16 bit external bus switching at 60 MHz, three serial ports and the converters running spends a measurable share of that on the I/O pins rather than the core, and the external memory devices add their own heat inside the same enclosure.

Where this order code fits

It is the 768 Kbyte STM32F205 in the 144 pin body, the pin rich part of the range without a network interface, for instruments that need an external memory bus and a wide set of serial ports. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Does this part have Ethernet? No. The 10/100 MAC and the camera interface are STM32F207 features. This code is the STM32F205 equivalent in the same package, pinout and memory, and the networked version is STM32F207ZFT6.

What is the SRAM on the 768 Kbyte density? 112 Kbytes of SRAM1 plus 16 Kbytes of SRAM2, 128 Kbytes in total, plus 4 Kbytes of backup SRAM in the VBAT domain. The 256 Kbyte part has 80 plus 16 Kbytes.

How many external memory banks can be used at once? Four chip selects are bonded on this package, so up to four devices on the same bus, each with its own timing register. On the 100 pin body only one bank is usable at a time.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.