Contact Us

STM32F205ZCT6

Brand: ST
ST STM32F205ZCT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F205ZCT6 — MCU & Embedded Processors | Superb Automation

STM32F205ZCT6

ST — MCU & Embedded Processors

Product Overview

The STM32F205ZCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F205ZCT6: 256 Kbyte, LQFP144 body

STM32F205ZCT6 is a member of the STM32F205 and STM32F207 performance line described by DS6329 Rev 18. The order code fixes 256 Kbytes of Flash, 96 Kbytes of SRAM, the LQFP144 body at 20 x 20 mm with 144 pins, 114 general purpose I/O and 16 external channels on each of the 12 bit converters, and the core runs at up to 120 MHz from a 1.8 to 3.6 V supply.

Order code and memory

Order codeSTM32F205ZCT6
Program Flash256 Kbytes
SRAM96 Kbytes
PackageLQFP144, 20 x 20 mm, 144 pins
Maximum general purpose I/O114
Analog input channels16 external channels per converter
Digital to analog converternot present
External memory controllerfull flexible static memory controller with four chip selects, NOR, PSRAM, SRAM, NAND and Compact Flash support
Supply voltage1.8 to 3.6 V
Maximum CPU clock120 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS6329 Rev 18

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 120 MHz with the adaptive real time accelerator, 1.25 DMIPS per MHz, 150 DMIPS, a memory protection unit and single cycle multiply and divide
Clock sources4 to 26 MHz high speed external crystal, 16 MHz factory trimmed internal RC, 32.768 kHz low speed internal and external sources, a main PLL and a separate audio PLL for the I2S blocks
Timerstwo advanced-control 16 bit timers with complementary outputs and dead time, four full featured general purpose timers of which TIM2 and TIM5 are 32 bit, six further general purpose 16 bit timers, two basic timers, the independent and window watchdogs, the SysTick counter and the RTC, which is the seventeen the cover counts
Serial interfacesthree SPI blocks two of which mux to I2S, three I2C blocks, four USARTs and two UARTs, two CAN 2.0B active controllers and one SDIO interface
DMAtwo DMA controllers with eight streams each and a FIFO per stream, sixteen streams in total, with circular buffer support
ADCthree 12 bit successive approximation converters with a 0.5 microsecond conversion time, each sharing up to 16 external channels, up to 24 channels across the three on the larger bodies and up to 6 Msps in triple interleaved mode
DACtwo 12 bit channels with output buffers
Ethernetnot present, Ethernet is an STM32F207 feature
Camera interfacenot present on the STM32F205
Cryptographic accelerationnot present on this part
Programmable voltage detectorprogrammable voltage detector with selectable thresholds, plus power on reset, power down reset and brownout reset
Debug portserial wire debug and JTAG, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC, the 4 Kbytes of backup SRAM and the backup registers alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C and 1 kcycle at 105 C, with 30 years of retention at 85 C after one kcycle, 20 years at 55 C after 10 kcycles and 10 years at 105 C
Thermal resistance junction to ambient40 C/W on this package
Input tolerancealmost all inputs 5 V tolerant, with fast I/O toggling to 60 MHz on the larger bodies
USBone OTG full speed port on the device pins and one OTG high speed port that needs an external ULPI PHY
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The pairing of 256 Kbytes of Flash with 96 Kbytes of SRAM is unusual at the top of a pin range and it reflects what this code is for: a board with external memory. With a full flexible static memory controller and 114 pins, the internal Flash holds the bootloader and the real time code while the application and the data buffers live in the external device. Buying more internal Flash on this body is often wasted money.

The 144 pin LQFP is rated 40 C/W, better than either of the smaller bodies, so at 85 C ambient the dissipation budget is about 500 mW. The larger body also spreads the I/O current over more pins, which matters on a board that drives an external memory bus at 60 MHz: the address and data lines switch continuously and the current is spread across 30 or so pins rather than concentrated on a few.

The memory controller on this body is the full version: four chip selects, separate address and data buses, NOR, PSRAM, SRAM, NAND and Compact Flash timing, with the timing registers per bank. That is what makes an external 16 bit SRAM at zero wait states possible, and it is also what makes the pin count jump from 82 to 114 unavoidable, because the address, data and control lines have to be bonded.

This part has no Ethernet MAC, which on a 144 pin board with an external memory bus is often the deciding check. Boards that were started from this code and then asked for a network port need STM32F207ZCT6, which is the same package, pinout and memory with the MAC and the camera interface added. Substituting the other direction, F207 for F205, is safe on the board and only adds cost.

The 256 Kbyte Flash is rated 10 kcycles of endurance at the industrial range with 30 years of retention at 85 C after one kcycle. On a board where the application runs from external memory, the internal Flash is mostly read at boot, so the endurance figure is rarely the constraint; on a board that stores parameters there, the 4 Kbytes of backup SRAM in the VBAT domain is the better place for the values written often.

Where this order code fits

It is the smallest memory option in the 144 pin body, 256 Kbytes of Flash with 96 Kbytes of SRAM and 114 general purpose pins, for boards that need the pin count and the memory controller more than they need memory. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What is the difference between this part and STM32F207ZCT6? The MAC and the camera interface. The F207 code adds the 10/100 Ethernet controller with its own DMA and the parallel camera interface on the same package, pinout, memory and speed. Firmware written for the F205 runs on the F207, but not the reverse when the network or camera is used.

Can the four chip selects be used at the same time? Yes on this package. The four chip selects of the memory controller are bonded here, which is not the case on the 100 pin body where only one bank is usable. Boards with a NOR, a NAND and an SRAM on the same bus need this package or larger.

Is 256 Kbytes of internal Flash enough at 120 MHz? It depends on where the code runs. With the memory controller available, a board can run the application from external memory and keep the internal Flash for the bootloader and the interrupt heavy routines, in which case 256 Kbytes is generous. A board that must run everything from internal Flash needs one of the larger densities.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.