Contact Us

STM32F103ZDT6

Brand: ST
ST STM32F103ZDT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F103ZDT6 — MCU & Embedded Processors | Superb Automation

STM32F103ZDT6

ST — MCU & Embedded Processors

Product Overview

The STM32F103ZDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F103ZDT6: 384 Kbytes with 112 I/Os in LQFP144

STM32F103ZDT6 sits in the middle of the 144 pin high density range: 384 Kbytes of flash, 64 Kbytes of SRAM, three 12 bit converters on 21 channels, two DAC channels, eleven timers and the full memory controller, in a 20 by 20 mm quad flat body. The C code is 256 Kbytes and the E code is 512 Kbytes, both on the same die and the same pinout, so the three are a single choice made three times.

Where the peripheral count lands

Thirteen communication interfaces: three SPI ports with two I2S channels, two I2C ports, five USARTs, an SDIO interface, a USB 2.0 full speed device port and a CAN 2.0B active controller. Four general purpose timers, two advanced control timers with dead time and break inputs, two basic timers and two watchdogs make up the eleven. On a board that runs two three phase motor drives, the two advanced timers are the reason for choosing the high density line at all, because the medium density parts carry only one.

Values at a glance

ParameterValueNote
Core and clockCortex-M3, 72 MHzTwo APB buses, 1.25 DMIPS/MHz
Flash, SRAM384 Kbytes, 64 Kbytes256 Kbyte ZC and 512 Kbyte ZE codes share the body
PackageLQFP144, 20 by 20 mmLFBGA144 is the 10 by 10 mm alternative
I/O112 pinsPorts A to G, nearly all 5 V tolerant
ADC, DAC3 converters, 12 bit, 21 channels; 2 DAC channelsDual sample and hold, temperature sensor on chip
External memoryFSMC, four chip selectsMultiplexed NOR, PSRAM, NAND support
Communication3 SPI, 2 I2S, 2 I2C, 5 USART, SDIO, USB, CANSDIO supports high capacity cards
TemperatureMinus 40 to plus 85 CCode 7 raises the ambient limit to 105 C

Two advanced timers is the motor control argument

A three phase inverter needs three complementary pairs with dead time and a break input, which is exactly what one advanced timer provides. Two independent drives, or one drive plus a power factor correction stage that also needs complementary outputs, use both timers at once and leave the four general purpose timers for encoder capture, PWM dimming and time keeping. On the medium density line the same job would need external logic or a second microcontroller, and that is the honest reason this density exists in the range.

Substitution inside the density set

Because the ZC, ZD and ZE codes share a die and a package, moving between them changes the linker memory map and nothing else on the board. A build short of the ZD code can take the ZE code with a firmware rebuild, and the reverse works only if the image fits in 384 Kbytes. The paperwork that keeps this clean is a microcontroller cross reference row listing all three codes, an obsolescence plan for the family as a whole, and an incoming inspection plan for open market purchases where date code and packaging have to be checked rather than assumed.

Common questions

Do the three converters share a reference? They share VREF+ and VDDA, and each has its own sample and hold. Interleaved operation needs a common trigger from a timer for the converters to be phase related.

How many timers can generate PWM at once? All four general purpose timers plus both advanced timers, subject to the pin conflicts on the alternate function map. The pin table is the limit rather than the timers.

Is the 21 channel ADC count reached on this package? Yes, this is the body where all 21 analog inputs are bonded out. The 100 pin version stops at 16 and the 64 pin at 16 as well.