Contact Us

STM32F102C6T6A

Brand: ST
ST STM32F102C6T6A is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F102C6T6A — MCU & Embedded Processors | Superb Automation

STM32F102C6T6A

ST — MCU & Embedded Processors

Product Overview

The STM32F102C6T6A from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F102C6T6A: 32 Kbyte, LQFP48 body

STM32F102C6T6A is a member of the STM32F102 USB access line low density described by DS5934 Rev 6. The order code fixes 32 Kbytes of Flash, 6 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 48 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F102C6T6A
Program Flash32 Kbytes
SRAM6 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this body
Supply voltage2.0 to 3.6 V
Maximum CPU clock48 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS5934 Rev 6

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 48 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 48 MHz core clock, external crystal range 4 to 16 MHz
Timerstwo general-purpose 16 bit timers, the independent and window watchdogs and the SysTick counter, which is the five the cover counts
Serial interfacesone SPI block, one I2C block and one USART on the 48 pin body, a second USART on the 64 pin body, plus the USB device port
DMADMA controller that serves the USART, the SPI and the converter
ADC12 bit successive approximation, 1.2 microsecond conversion with APB2 at 12, 24 or 48 MHz, 10 channels on 48 pins and 16 channels on 64 pins
DACnot present on this line
Programmable voltage detectoreight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainVBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off
Flash endurance and retention10 kcycles, 30 years of retention at 85 C after 1000 cycles
Thermal resistance junction to ambient55 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBfull speed device at 12 Mbit/s, 48 MHz clock taken from the PLL with an external crystal as the source
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The A after the temperature digit is an internal code, and on the STM32F102 line it decides which document describes the electrical behaviour. Footnote 1 of Table 3 in DS5934 Rev 6 says that orderable parts without the A internal code take their reference from the STM32F102x8/B medium density datasheet, so the A marked part is the one the low density document actually describes. Memory, pin count and package are the same either way, but a qualification report has to name the document it was written against.

USB is the reason this line exists, and it is a full speed device port at 12 Mbit/s, not a host and not a high speed port. The 48 MHz USB clock has to come from the PLL, and the datasheet requires an external crystal as the clock source, so a board that hoped to run USB from the internal RC cannot. That single requirement decides two pins and one component on a 48 pin board before any other function is considered.

The low density interface set is deliberately small: one SPI block, one I2C block, one USART on the 48 pin body, and a second USART on the 64 pin body, plus the USB port. With 37 general purpose I/O and 10 converter channels, a board that needs a second serial port, an SPI device and an I2C device at the same time is at the limit of this package and should be looking at the 64 pin 32 Kbyte code or at the medium density parts.

The 6 Kbytes of SRAM is the largest in the low density USB range, compared with 4 Kbytes on the 16 Kbyte code, and it is what makes a USB device stack practical. An endpoint buffer set plus a control transfer buffer plus the application state machine is a kilobyte or more before the converter and the serial buffers are counted. On a 6 Kbyte part that is workable; on the 4 Kbyte code it is tight enough to change what the firmware can do.

The converter runs a 1.2 microsecond conversion when APB2 is at 12, 24 or 48 MHz, which the datasheet calls out as a condition rather than a property of the converter. The clock tree therefore matters: the same silicon converts in 1.2 microseconds or slower depending on how APB2 is divided, and a firmware that needs a fixed sample period has to derive it from the actual APB2 frequency rather than from the nominal figure.

At 55 C/W on the LQFP48 body the junction rises 20 C above an 85 C ambient at about 360 mW. A USB device board usually draws its supply from the bus or from a local regulator, and the transceiver current is part of that budget. A board that runs the part from a USB 5 V rail through a linear regulator has to account for the regulator dissipation as well, which on a small enclosure is often the hotter component.

Flash endurance is 10 kcycles with 30 years of retention at 85 C after 1000 cycles, and the low density parts are production data in DS5934 Rev 6. Because a USB device is often reflashed during development over the same port, the endurance question is usually about the programming cycles during development rather than about the field life, and a bootloader that writes only changed pages is what keeps the development count low.

Where this order code fits

It is the 32 Kbyte USB access line part in a 48 pin body, used where a board needs a full speed device port and a 12 bit converter and nothing larger than a 7 x 7 mm package. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What does the A in the order code mean? It is an internal code that determines which datasheet describes the electrical behaviour. Parts without the A take their reference from the STM32F102x8/B medium density document, while this code is described by DS5934 Rev 6. The memory, the package and the pin count are the same in both cases.

Can USB run from the internal oscillator? No. The USB clock has to be 48 MHz from the PLL with an external crystal as the source. A board without a crystal cannot use the USB port, which is why the crystal is usually the first component placed on this part.

Is this part pin compatible with the STM32F103C8T6? The two families share the 48 pin LQFP outline and much of the pin map, but they are different devices with different peripheral sets and different memory maps. Compatibility at the package level does not mean a board built for one runs unchanged on the other.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.