Contact Us

STM32F102C6T6

Brand: ST
ST STM32F102C6T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F102C6T6 — MCU & Embedded Processors | Superb Automation

STM32F102C6T6

ST — MCU & Embedded Processors

Product Overview

The STM32F102C6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F102C6T6: 32 Kbyte, LQFP48 body

STM32F102C6T6 is a member of the STM32F102 USB access line low density described by DS5934 Rev 6. The order code fixes 32 Kbytes of Flash, 6 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 external channels on each of the 12 bit converters, and the core runs at up to 48 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F102C6T6
Program Flash32 Kbytes
SRAM6 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 external channels per converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock48 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS5934 Rev 6

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 48 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 48 MHz core clock, external crystal range 4 to 16 MHz
Timerstwo general purpose 16 bit timers with four compare channels each, the independent and window watchdogs and the SysTick counter, which is the five the cover counts
Serial interfacesone SPI block, one I2C block, two USARTs of which the second only comes out on the 64 pin body, and one USB full speed device port
DMA7 channel DMA controller serving the USARTs, the SPI and the converter
ADC12 bit successive approximation, 1.2 microsecond conversion with APB2 at 12, 24 or 48 MHz, 10 channels on 48 pins and 16 on 64 pins
DACnot present on this line
Ethernetnot present on this line
Camera interfacenot present on this line
Cryptographic accelerationnot present on this line
Programmable voltage detectorprogrammable voltage detector with eight falling thresholds from 2.00 V to 2.88 V nominal
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Flash endurance and retention10 kcycles with 30 years of retention at 85 C after 1 kcycle
Thermal resistance junction to ambient55 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBfull speed device at 12 Mbit/s, with the 48 MHz clock taken from the PLL and an external crystal as the reference
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The order code reads in four fields: C is the 48 pin LQFP at 7 x 7 mm, 6 is 32 Kbytes of Flash, T is the LQFP body and the last 6 is the industrial grade of minus 40 to plus 85 C ambient. Nothing in the string states the SRAM, which is 6 Kbytes on this density and only 4 Kbytes on the 16 Kbyte code directly below it. A substitute check has to compare the memory column of Table 2 rather than the order string, because both codes end in C6T6 or C4T6 and look interchangeable on a purchase order.

USB on this line is a device port only and it needs a crystal. The 48 MHz USB clock is taken from the PLL, and the internal 8 MHz RC is trimmed to about one percent at 25 C but drifts to roughly two percent over temperature, which is outside what a full speed link tolerates end to end. A 4 to 16 MHz crystal on the high speed oscillator is therefore part of the bill of materials on any board that actually enumerates, and a board that omits it will negotiate at best intermittently.

The 512 byte packet memory of the USB peripheral is fixed in silicon and does not come out of the 6 Kbytes of SRAM. What does come out of SRAM is everything the firmware keeps around it: the endpoint buffers the application copies into, the descriptor table, the control transfer state machine and the stack. On 6 Kbytes that leaves room for a small command parser and a ring buffer, which is enough for a data logger or a keyboard class device and not enough for a file system on top of a mass storage class.

Ten converter channels are bonded out on the 48 pin body and they share port A, port B and port C with the USB pins, the crystal and the debug port. PA11 and PA12 are the USB pair, so they are gone before the analog assignment starts, and the two pins of the crystal take two more. A board that wants six analog inputs, USB and serial wire debug has about 28 free pins for everything else, which is the number to count rather than the headline 37.

The 48 pin LQFP is rated 55 C/W junction to ambient, so the 20 C between the 85 C ambient grade and the 105 C junction allows roughly 360 mW of total dissipation. The core at 48 MHz plus the USB transceiver plus the converter running continuously is inside that budget, but a board that sinks 8 mA into ten indicator LEDs spends most of it on the pins. The I/O current is the first thing to add up on a part this small, not the core current.

Where this order code fits

It is the 32 Kbyte, 48 pin member of the USB access line, used on instrument front ends, dongles and small controllers that need a full speed device port and 32 bit math on a 7 x 7 mm body. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Can the USB port run from the internal oscillator without a crystal? No. The 48 MHz USB clock is derived from the PLL, and the internal RC that feeds it is trimmed to about one percent at 25 C with a drift near two percent over the full range. A full speed device link does not keep to the required tolerance with that error, so a 4 to 16 MHz crystal is required on any board that enumerates reliably.

What is the difference between STM32F102C6T6 and STM32F102C4T6? Flash and SRAM. The C6 code carries 32 Kbytes of Flash and 6 Kbytes of SRAM, the C4 code 16 Kbytes and 4 Kbytes. Package, pin count, converter channels and the peripheral set are the same, so the two are interchangeable on a board only when the firmware fits in the smaller memory.

Does this part have CAN or a digital to analog converter? Neither. The USB access line carries no CAN controller and no DAC at any density. Boards that need either move to the STM32F103 or STM32F105 lines, which bring the CAN controller and, on the F103 high density parts, two 12 bit DAC channels.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.