Contact Us

STM32F101ZGT6

Brand: ST
ST STM32F101ZGT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101ZGT6 — MCU & Embedded Processors | Superb Automation

STM32F101ZGT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101ZGT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101ZGT6: 1 Mbyte, LQFP144 body

STM32F101ZGT6 is a member of the STM32F101 XL density access line described by DocID16553 Rev 5. The order code fixes 1024 Kbytes of Flash, 80 Kbytes of SRAM, the LQFP144 body at 20 x 20 mm with 144 pins, 112 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101ZGT6
Program Flash1 Mbyte / 1024 Kbytes Kbytes
SRAM80 Kbytes
PackageLQFP144, 20 x 20 mm, 144 pins
Maximum general purpose I/O112
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllerfull controller, port G available
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 with memory protection unit at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersup to ten 16 bit general purpose timers with up to four compare channels each and two 16 bit basic timers, 15 timers in total with the watchdogs
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks, with UART5 outside the DMA controller
DMA12 channels split across two DMA controllers
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop currentstop and standby figures follow the high density tables of this line
Standby current1.9 uA typical in standby with the RTC off on the neighbouring high density grades
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, with two Flash banks that support read while write
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

G is 1 Mbyte of Flash and Z is the 144 pin body. DocID16553 gives 80 Kbytes of SRAM, 112 general purpose I/O, 16 converter channels, two DAC channels, five USARTs, three SPI blocks, two I2C blocks, up to ten general purpose timers and two basic timers, 15 timers in total, with a 12 channel DMA controller split across two blocks.

The Flash is organised as two banks with read while write, so a new image can be written into one bank while the old image keeps running from the other. That is the difference from the high density 512 Kbyte part, which has a single bank and cannot update in place without a gap.

The core adds a memory protection unit, which lets an RTOS mark a task as non privileged and catch a stray pointer before it corrupts another task. The lower densities do not carry that block, so a product that depends on it cannot step down the line.

One detail from the DMA chapter is worth stating: every interface can be served by the DMA controller except UART5, so a board that puts a high rate link on UART5 will service it in the interrupt. The 144 pin body still has the full external memory controller and port G.

The memory protection unit is what makes a task based system worth running on a single core: it marks a task as non privileged and traps a write outside its own region, which a stray pointer from a protocol parser would otherwise carry into another task. The unit covers the 80 Kbytes of SRAM and the peripheral space.

Where this order code fits

It is the 1 Mbyte part in the XL density line, with two Flash banks, 80 Kbytes of SRAM and a memory protection unit, used where a field update has to keep the old image alive. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What does read while write give me? Two Flash banks, so the application can run from one while the other is erased and rewritten. A power failure during the update leaves the old image intact, which is not true on the single bank part.

How much SRAM and how is it organised? 80 Kbytes, against 48 Kbytes on the 512 Kbyte high density part. The extra memory and the protection unit are the two reasons to move up from that part.

Is UART5 served by DMA? No. The reference manual states that every interface can be served by the DMA controller except UART5, so a high rate link on that port has to be handled in the interrupt routine or moved to another USART.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.

TR for tape and reel and xxx for a programmed part sit in the options field, so the plain code names a tray device. Two features justify this part over the 512 Kbyte high density one: 1 Mbyte in two banks with read while write for a field update, and a memory protection unit that traps a task writing outside its region. Both are invisible on a board and both change what the firmware can promise. The 15 timers, 12 DMA channels and five USARTs are the same class as the high density part, so the move is about memory and protection rather than about peripherals.