Contact Us

STM32F101ZET6

Brand: ST
ST STM32F101ZET6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101ZET6 — MCU & Embedded Processors | Superb Automation

STM32F101ZET6

ST — MCU & Embedded Processors

Product Overview

The STM32F101ZET6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101ZET6: 512 Kbyte, LQFP144 body

STM32F101ZET6 is a member of the STM32F101 high density access line described by DocID14610 Rev 9. The order code fixes 512 Kbytes of Flash, 48 Kbytes of SRAM, the LQFP144 body at 20 x 20 mm with 144 pins, 112 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101ZET6
Program Flash512 Kbytes
SRAM48 Kbytes
PackageLQFP144, 20 x 20 mm, 144 pins
Maximum general purpose I/O112
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllerfull controller, port G available
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersfour 16 bit general purpose timers with up to four compare channels each, two 16 bit basic timers that drive the DAC, plus the independent and window watchdogs and the SysTick counter
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks
DMA12 channel DMA controller
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop current24.5 uA typical and 365 uA maximum at 85 C from a 3.3 V supply
Standby current1.9 uA typical with the low speed oscillator and RTC off, 2.8 uA with them on and 5 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

Z is 144 pins and E is 512 Kbytes of Flash. Table 2 of DocID14610 lists 48 Kbytes of SRAM, 112 general purpose I/O, 16 converter channels, two DAC channels, five USARTs, three SPI blocks, two I2C blocks and 12 DMA channels, with 36 MHz and 2.0 to 3.6 V.

This is the top of the single bank high density range, so the program array is written as one region and a firmware update replaces it in place. The XL density 1 Mbyte part adds a second bank with read while write, which is the feature a field update routine needs if the old image has to keep running.

Flash endurance is 10 kcycles with 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles, so logging parameters into the same page at a high rate is not what this memory is for.

48 Kbytes of SRAM with the full external bus is enough to hold a working set while a NAND page streams through the DMA controller, and the 46 C/W package figure allows 434 mW at 85 C ambient for the whole part including I/O current.

The internal RC runs at 8 MHz with 1.1 percent accuracy at 25 C and 2.2 percent over the full range, and the PLL multiplies it to the 36 MHz core clock. A board that uses the RC instead of a crystal accepts that the whole clock tree, including the external bus timing, moves by that percentage over temperature.

Where this order code fits

It is the largest single bank part in the access line, 512 Kbytes of Flash and 112 I/O with the full external memory controller. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How does it compare with the 1 Mbyte part? Same package, same 112 I/O, same peripherals. The XL density part doubles the Flash to 1 Mbyte in two banks, raises SRAM to 80 Kbytes and adds a memory protection unit.

Is the Flash organised in one bank? Yes, on the high density line the array is a single bank. Read while write, where one bank is written while code runs from the other, is the XL density feature.

What temperature range does the 6 suffix cover? Minus 40 to plus 85 C ambient, with a junction limit of 105 C. Each grade fixes both the ambient range and the junction limit, and the datasheet shows how to check the junction from the dissipation.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.

Packing and programming are options after the base code: TR is tape and reel and xxx is a programmed part, and the plain string is a tray order. On 512 Kbytes of single bank Flash the update strategy is the decision to confirm early, because replacing a running image requires a gap that a two bank XL density part does not have, and that part costs less than a board spin later. The 48 Kbytes of SRAM and the 12 channel DMA controller are what make a NAND page stream practical, and both are shared with the display if one is fitted on the same controller.