Contact Us

STM32F101ZCT6

Brand: ST
ST STM32F101ZCT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101ZCT6 — MCU & Embedded Processors | Superb Automation

STM32F101ZCT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101ZCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101ZCT6: 256 Kbyte, LQFP144 body

STM32F101ZCT6 is a member of the STM32F101 high density access line described by DocID14610 Rev 9. The order code fixes 256 Kbytes of Flash, 32 Kbytes of SRAM, the LQFP144 body at 20 x 20 mm with 144 pins, 112 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101ZCT6
Program Flash256 Kbytes
SRAM32 Kbytes
PackageLQFP144, 20 x 20 mm, 144 pins
Maximum general purpose I/O112
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllerfull controller, port G available
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersfour 16 bit general purpose timers with up to four compare channels each, two 16 bit basic timers that drive the DAC, plus the independent and window watchdogs and the SysTick counter
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks
DMA12 channel DMA controller
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop current24.5 uA typical and 365 uA maximum at 85 C from a 3.3 V supply
Standby current1.9 uA typical with the low speed oscillator and RTC off, 2.8 uA with them on and 5 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

Z is 144 pins and C is 256 Kbytes. DocID14610 gives 32 Kbytes of SRAM, 112 general purpose I/O, 16 converter channels, two DAC channels, five USARTs, three SPI blocks, two I2C blocks, four general purpose timers, two basic timers and a 12 channel DMA controller.

Unlike the 100 pin body, this package has the full flexible static memory controller with all four chip selects and port G, so the controller interrupt line and the 8080 and 6800 LCD parallel interface are both usable. That is the difference a board sees when it moves from 100 to 144 pins with the same Flash size.

112 I/O is more than most boards can use, and the practical limit becomes the total I/O current rather than the pin count. The package is rated 46 C/W junction to ambient, so the 20 C margin at 85 C ambient allows about 434 mW of total dissipation.

The 256 Kbyte array with 32 Kbytes of SRAM is small for a board that carries a display and an external bus, which is why this part is normally chosen for a fixed image with an external memory device beside it rather than for a large application.

The detector has eight levels from 2.08 V to 2.88 V nominal and can be routed to an interrupt. With the full external memory controller in use, that interrupt is the moment to stop bus activity, because a write in progress when the rail falls leaves the external device in an unknown state and the controller cannot recover it.

Where this order code fits

It is the 144 pin, 256 Kbyte high density part, the smallest body with the full external memory controller and 112 general purpose I/O. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Which chip selects are available? All four on this package, with port G bonded out, so the controller interrupt and the full memory map are usable. The 100 pin body is limited to bank 1 and bank 2.

Can a parallel display be connected? Yes, the 8080 and 6800 interface is carried by the flexible static memory controller and this package exposes all of it. A framebuffer would normally sit in external memory.

How many I/O are there? 112 general purpose I/O, all mappable on the 16 external interrupt vectors and almost all 5 V tolerant on the input side.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the ADC DAC Cross Reference page sets out the checks that keep a substitute from failing on the bench.

The ordering scheme carries TR for tape and reel and xxx for a programmed part after the base code, so packing is an explicit line on the order. The capability that justifies the 144 pin body is the full memory controller with four chip selects and port G, which is what allows the controller interrupt line and the parallel display interface to be used together while the 32 Kbytes of SRAM hold the working set. The 112 I/O are all mappable on the 16 external interrupt vectors, so a board with many switches can use interrupts instead of polling, which is what keeps the core free for the display refresh.