Contact Us

STM32F101VDT6

Brand: ST
ST STM32F101VDT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101VDT6 — MCU & Embedded Processors | Superb Automation

STM32F101VDT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101VDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101VDT6: 384 Kbyte, LQFP100 body

STM32F101VDT6 is a member of the STM32F101 high density access line described by DocID14610 Rev 9. The order code fixes 384 Kbytes of Flash, 48 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101VDT6
Program Flash384 Kbytes
SRAM48 Kbytes
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O80
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllerbank 1 and bank 2 only, no port G
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersfour 16 bit general purpose timers with up to four compare channels each, two 16 bit basic timers that drive the DAC, plus the independent and window watchdogs and the SysTick counter
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks
DMA12 channel DMA controller
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop current24.5 uA typical and 365 uA maximum at 85 C from a 3.3 V supply
Standby current1.9 uA typical with the low speed oscillator and RTC off, 2.8 uA with them on and 5 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

V is 100 pins and D is 384 Kbytes. DocID14610 gives 48 Kbytes of SRAM, 80 general purpose I/O, 16 converter channels, two DAC channels, five USARTs, three SPI blocks, two I2C blocks and a 12 channel DMA controller for the 100 pin row.

The flexible static memory controller appears here but with two limits stated in Table 2 note 1: only bank 1 and bank 2 are available, bank 1 supports a multiplexed NOR or PSRAM device on the NE1 chip select, and bank 2 supports a 16 or 8 bit NAND device on the NCE2 chip select. Port G is not bonded out, so the interrupt line of the controller cannot be used.

That note is the practical difference between this part and the 144 pin version. A board that wants two chip selects for SRAM plus a display interface needs the larger body, while a board that only needs one NAND device or one multiplexed PSRAM is served here.

SRAM of 48 Kbytes with a 12 channel DMA controller is what makes the external bus useful: a NAND page of 2 Kbytes arrives through the DMA controller while the core runs the file system, and the 48 Kbytes hold the cache. Stop current on this line is 24.5 uA typical and 365 uA maximum at 85 C.

The voltage detector and the reset circuit are the two levels of protection on the supply: the detector has eight thresholds between 2.08 V and 2.88 V nominal, while the power on and power down reset circuit works to a fixed threshold of its own. On a board with external memory the detector interrupt is normally used to close the file system before the bus loses its supply.

Where this order code fits

It is the 100 pin, 384 Kbyte high density part, the first body with an external memory bus and 80 general purpose I/O. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Which memory types can be connected? A multiplexed NOR or PSRAM device on bank 1 through the NE1 chip select, and a 16 or 8 bit NAND device on bank 2 through NCE2. The other chip selects belong to the 144 pin body.

Why is port G relevant? Because the controller interrupt line is not available on this package without it. A board that relied on the interrupt to flag a completed transfer has to poll the status register instead.

How many I/O are usable? 80 general purpose I/O, against 51 on the 64 pin body and 112 on the 144 pin body, and all of them are mappable on the 16 external interrupt vectors.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the ADC DAC Cross Reference page sets out the checks that keep a substitute from failing on the bench.

TR is tape and reel and xxx is a programmed part, both after the base code, so a purchase order has to state packing explicitly. On a 100 pin part the bus is the thing to confirm: bank 1 takes one multiplexed NOR or PSRAM device and bank 2 takes one 16 or 8 bit NAND, and a product that needs a third chip select belongs on the 144 pin body where the full controller is bonded out. Port G is not available here, so the controller interrupt line cannot be used and a driver that waits on it has to poll the status register, which changes the timing budget of the external memory access.