Contact Us

STM32F101VCT6

Brand: ST
ST STM32F101VCT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101VCT6 — MCU & Embedded Processors | Superb Automation

STM32F101VCT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101VCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101VCT6: 256 Kbyte, LQFP100 body

STM32F101VCT6 is a member of the STM32F101 high density access line described by DocID14610 Rev 9. The order code fixes 256 Kbytes of Flash, 32 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101VCT6
Program Flash256 Kbytes
SRAM32 Kbytes
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O80
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllerbank 1 and bank 2 only, no port G
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersfour 16 bit general purpose timers with up to four compare channels each, two 16 bit basic timers that drive the DAC, plus the independent and window watchdogs and the SysTick counter
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks
DMA12 channel DMA controller
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop current24.5 uA typical and 365 uA maximum at 85 C from a 3.3 V supply
Standby current1.9 uA typical with the low speed oscillator and RTC off, 2.8 uA with them on and 5 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

V is 100 pins and C is 256 Kbytes of Flash. Table 2 of DocID14610 lists 32 Kbytes of SRAM, 80 general purpose I/O, 16 converter channels, two DAC channels, three SPI blocks, two I2C blocks, five USARTs and a 12 channel DMA controller, with 36 MHz across 2.0 to 3.6 V.

The external bus is the reason to take this body over the 64 pin part, and it comes with the same two bank limit: bank 1 for a multiplexed NOR or PSRAM through NE1, bank 2 for a 16 or 8 bit NAND through NCE2. Port G is absent, so the controller interrupt line is not usable.

32 Kbytes of SRAM is half of the 144 pin high density figure, so a board that keeps a 2 Kbyte NAND page buffer, a 4 Kbyte file cache and a 4 Kbyte communication buffer still has room, while one that wants a display framebuffer does not.

The 100 pin LQFP leaves 80 I/O after the bus pins are assigned, and the 12 channel DMA controller removes the need to service the bus in an interrupt. At 36 MHz the core can sustain about 1.25 DMIPS per MHz, which is why a 100 pin board with an external bus still runs a small file system comfortably.

The internal oscillator is within 1.1 percent at 25 C and 2.2 percent over the temperature range, so a board that keeps a crystal is buying accuracy rather than start up time. With the external bus running from the same clock, the RC option also moves the memory timing, which is why a crystal is usual on this part.

Where this order code fits

It is the 256 Kbyte, 100 pin high density part, placed between the 64 pin code and the 144 pin version where the external bus first becomes available. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How much Flash do the 100 pin parts offer? 256, 384 and 512 Kbytes for the high density line and 64 or 128 Kbytes for the medium density line, and the XL density line adds 768 Kbytes and 1 Mbyte in the same 100 pin body.

Can two chip selects be used? Only the two banks described in Table 2 are available here. A third chip select requires the 144 pin body, where the full controller is present.

What is the difference from the 64 pin RCT6? The external memory bus, 29 more general purpose I/O and the larger body. Flash and SRAM are the same 256 Kbytes and 32 Kbytes.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.

The options field carries TR for tape and reel and xxx for a programmed part, and the base code on its own is a tray device. The other check is the memory split: 32 Kbytes of SRAM against 256 Kbytes of Flash on this body leaves the external bus as the place for anything large, and a NAND page of 2 Kbytes plus a file cache fits inside the 32 Kbytes while a framebuffer does not. The 100 pin package is rated 46 C/W, so the 20 C junction margin at 85 C ambient is about 434 mW in total, and a board that drives external loads from 80 I/O can reach that before the core is busy.