Contact Us

STM32F101V8T6

Brand: ST
ST STM32F101V8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101V8T6 — MCU & Embedded Processors | Superb Automation

STM32F101V8T6

ST — MCU & Embedded Processors

Product Overview

The STM32F101V8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101V8T6: 64 Kbyte, LQFP100 body

STM32F101V8T6 is a member of the STM32F101 medium density access line described by DocID13586 Rev 17. The order code fixes 64 Kbytes of Flash, 10 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101V8T6
Program Flash64 Kbytes
SRAM10 Kbytes
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O80
Analog input channels16 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersthree 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacesthree USARTs, two SPI blocks and two I2C blocks on 48 pins and above, two USARTs, one SPI and one I2C on the 36 pin body
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 and 100 pins
DACnot present on this line
Stop current14 uA typical and 180 uA maximum at 85 C from a 3.3 V supply
Standby current2 uA typical and 4 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

V is 100 pins and 8 is 64 Kbytes of Flash. Table 2 of DocID13586 puts the 100 pin medium density row at 10 Kbytes of SRAM, 80 general purpose I/O, 16 converter channels, three USARTs, two SPI and two I2C blocks, with three general purpose timers and a 7 channel DMA controller.

80 I/O with only 64 Kbytes of Flash is an unusual balance and it is exactly right for a machine control board: the pin count drives the enclosure and the harness, while the code is a state machine plus a few protocol handlers that fit in 64 Kbytes.

There is no external memory bus on the medium density line, so the extra pins are all application pins. A board that needs external RAM has to move to the high density 100 pin part, where the bus appears but 29 of the pins are shared with it.

The 100 pin LQFP is rated 46 C/W junction to ambient, which allows 434 mW inside the 20 C margin at 85 C ambient. That figure assumes the four sides of the package are soldered to a plane, and a socketed part will run hotter than the number suggests.

Serial wire debug and JTAG both come out on the 100 pin body, and the trace port shares pins with the low order port bits. On 80 I/O the debug pins are a small cost, but the trace pins are not free: they take four more, and a board that wants trace has to reserve them before the connector assignment is fixed.

Where this order code fits

It is the 64 Kbyte medium density part in a 100 pin body, chosen when the I/O count matters far more than the memory size. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Why a 100 pin body with 64 Kbytes? Because the I/O count follows the package and not the memory. A control board with 70 signals uses this part, while a board with 40 signals and the same code uses the 48 pin C8T6.

Are all 16 converter channels available? Yes, the 100 pin medium density row bonds out all 16 channels, and there is a single 12 bit converter shared between them.

Is there a DAC? No. Two 12 bit DAC channels are part of the high density and XL density lines only, so analog outputs here have to be external or built from a PWM channel and a filter.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the ADC DAC Cross Reference page sets out the checks that keep a substitute from failing on the bench.

Packing is stated separately from the part number, with TR for tape and reel and xxx for a programmed part in the options field. On the 100 pin medium density body the count that matters is 80 I/O with no external bus behind them, which is why this part suits a machine control board where the harness decides the pin count and the code stays inside 64 Kbytes. The three USARTs and two SPI blocks take part of those pins back, and the 10 Kbytes of SRAM is the term that limits buffers once a display and a converter stream share the same core.