STM32F101T8U6
Product Specifications
STM32F101T8U6
ST — MCU & Embedded Processors
Product Overview
The STM32F101T8U6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F101T8U6: 64 Kbyte, VFQFPN36 body
STM32F101T8U6 is a member of the STM32F101 medium density access line described by DocID13586 Rev 17. The order code fixes 64 Kbytes of Flash, 10 Kbytes of SRAM, the VFQFPN36 body at 6 x 6 mm with 36 pins, 26 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.
Order code and memory
| Order code | STM32F101T8U6 |
| Program Flash | 64 Kbytes |
| SRAM | 10 Kbytes |
| Package | VFQFPN36, 6 x 6 mm, 36 pins |
| Maximum general purpose I/O | 26 |
| Analog input channels | 10 of the 12 bit converter |
| Digital to analog converter | not present |
| External memory controller | not present on this line |
| Supply voltage | 2.0 to 3.6 V |
| Maximum CPU clock | 36 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide |
| Timers | three 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter |
| Serial interfaces | three USARTs, two SPI blocks and two I2C blocks on 48 pins and above, two USARTs, one SPI and one I2C on the 36 pin body |
| DMA | 7 channel DMA controller |
| ADC | 12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 and 100 pins |
| DAC | not present on this line |
| Stop current | 14 uA typical and 180 uA maximum at 85 C from a 3.3 V supply |
| Standby current | 2 uA typical and 4 uA maximum |
| Internal RC accuracy | 8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case |
| Flash endurance | not stated in this datasheet revision |
| Input tolerance | almost all inputs 5 V tolerant |
| USB | not present, USB full speed is the STM32F102 line |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
T is the 36 pin body, 8 is 64 Kbytes of Flash, U is the VFQFPN package at 6 x 6 mm and 6 is the industrial range. Table 2 of DocID13586 puts the 36 pin medium density row at 10 Kbytes of SRAM, 26 general purpose I/O, 10 converter channels, two USARTs, one SPI and one I2C.
26 usable I/O after the clock, reset, supply and debug pins is the constraint that decides most boards here. Two USARTs, one SPI and one I2C consume six pins between them, leaving 20 for the application, so a keypad and a display cannot both be direct wired.
The package is rated 18 C/W junction to ambient, the lowest figure in the family, because the exposed pad sits on the board copper. That makes the thermal path a matter of the pad and the vias under it rather than the package outline, and it is why this body can carry more current than the 48 pin part at the same ambient.
The 64 Kbyte array with 10 Kbytes of SRAM is the same memory as the 48 and 64 pin parts, so code moves between the three packages without a rebuild. What does not move is the peripheral count: 26 pins cannot expose the third USART or the second SPI block.
Two wire debug costs two of the 26 I/O and JTAG costs five, which is a fifth of the port on this body. The debug pins are shared with the application, so a board that needs all 26 has to disable the port in the option bytes after programming and accept that field rework then needs another entry point.
Where this order code fits
It is the 36 pin quad flat no lead version of the 64 Kbyte part, the smallest footprint in the access line, used where board area decides the choice. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
How many I/O can the application use? 26 in total, and that already excludes the supply, reset, clock and debug pins. Two USARTs, one SPI and one I2C take six of them, so the usable count for the application is around 20.
Is the thermal pad connected to ground? The exposed pad is the thermal path and is tied to the ground plane in the reference footprint. The 18 C/W figure assumes that pad is soldered to copper with a via field under it.
Can it be used at 5 V? No, the supply range is 2.0 to 3.6 V, and the 5 V tolerance applies to the inputs and not to the supply rail.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.
Packing lives in the options field of the ordering scheme, TR for tape and reel and xxx for a programmed part, and a 6 x 6 mm quad flat no lead body is normally handled in tape. The figure to confirm on 26 I/O is how many of the port pins the two USARTs, the SPI and the I2C take, because six of the 26 go to those blocks and the remaining 20 have to cover the converter inputs and the digital signal lines of the product. The 18 C/W thermal figure for this package is the lowest in the family, and it holds only when the exposed pad is soldered to a copper area with a via field under it.