Contact Us

STM32F101RET6

Brand: ST
ST STM32F101RET6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101RET6 — MCU & Embedded Processors | Superb Automation

STM32F101RET6

ST — MCU & Embedded Processors

Product Overview

The STM32F101RET6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101RET6: 512 Kbyte, LQFP64 body

STM32F101RET6 is a member of the STM32F101 high density access line described by DocID14610 Rev 9. The order code fixes 512 Kbytes of Flash, 48 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101RET6
Program Flash512 Kbytes
SRAM48 Kbytes
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllernot present on the 64 pin body
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersfour 16 bit general purpose timers with up to four compare channels each, two 16 bit basic timers that drive the DAC, plus the independent and window watchdogs and the SysTick counter
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks
DMA12 channel DMA controller
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop current24.5 uA typical and 365 uA maximum at 85 C from a 3.3 V supply
Standby current1.9 uA typical with the low speed oscillator and RTC off, 2.8 uA with them on and 5 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

R is 64 pins, E is 512 Kbytes of Flash and 6 is the industrial range. DocID14610 lists 48 Kbytes of SRAM for this part, with 51 general purpose I/O, 16 converter channels, two DAC channels, five USARTs, three SPI blocks, two I2C blocks and a 12 channel DMA controller.

Flash endurance on the high density line is 10 kcycles, with 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles, so a data logging scheme that rewrites a page every minute will still use an external EEPROM for anything that has to survive a decade.

The 512 Kbyte array is the largest in the high density line and the same size as the XL density entry part, but the XL part adds a second Flash bank with read while write, an 80 Kbyte SRAM and a memory protection unit. A firmware update that has to keep running from the old image needs the XL part, not this one.

At 45 C/W for the LQFP64 body, the 20 C junction margin at 85 C ambient allows 444 mW. A 36 MHz core with the converter, three SPI buses and 51 I/O switching is still well inside that, so the thermal question on this part is the external load rather than the core.

The voltage detector has eight levels between 2.08 V and 2.88 V nominal and can interrupt as well as reset. With 512 Kbytes of Flash the warning normally starts a checksum write or a controlled stop, because a rail that falls through 2.0 V during a Flash write leaves the page in an undefined state and the 10 kcycle endurance figure assumes completed writes.

Where this order code fits

It puts the largest high density array, 512 Kbytes, into a 64 pin footprint, for products whose code keeps growing but whose board outline is fixed. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is 512 Kbytes the top of the family? No. The XL density line goes to 768 Kbytes and 1 Mbyte in two banks, with 80 Kbytes of SRAM and a memory protection unit. This part is the top of the single bank high density range.

How many timer blocks are there? Four general purpose 16 bit timers with up to four compare channels each, two basic timers that drive the DAC, plus the two watchdogs and the SysTick counter.

Does the part support in application programming? Yes. The Flash can be written from the application, which is how the bootloader pattern works on this line, and the 10 kcycle endurance figure is what limits how often a page can be rewritten.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.

TR for tape and reel and xxx for a programmed part are the two options fields, and a code without them is a tray device that has to be packed by agreement. The practical limit on a 512 Kbyte single bank part is update behaviour: the array is written as one region, so a firmware update replaces the running image, and a product that cannot tolerate that gap belongs on the XL density part with two banks instead. Endurance is 10 kcycles with 30 years of retention at 85 C after one kcycle, and 20 years at 55 C after 10 kcycles, which is what limits a scheme that rewrites a page on every power cycle.