Contact Us

STM32F101RDT6

Brand: ST
ST STM32F101RDT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101RDT6 — MCU & Embedded Processors | Superb Automation

STM32F101RDT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101RDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101RDT6: 384 Kbyte, LQFP64 body

STM32F101RDT6 is a member of the STM32F101 high density access line described by DocID14610 Rev 9. The order code fixes 384 Kbytes of Flash, 48 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101RDT6
Program Flash384 Kbytes
SRAM48 Kbytes
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllernot present on the 64 pin body
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersfour 16 bit general purpose timers with up to four compare channels each, two 16 bit basic timers that drive the DAC, plus the independent and window watchdogs and the SysTick counter
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks
DMA12 channel DMA controller
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop current24.5 uA typical and 365 uA maximum at 85 C from a 3.3 V supply
Standby current1.9 uA typical with the low speed oscillator and RTC off, 2.8 uA with them on and 5 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

R is 64 pins and D is 384 Kbytes of Flash. Table 2 of DocID14610 lists 48 Kbytes of SRAM, 51 general purpose I/O, 16 converter channels, two 12 bit DAC channels, three SPI blocks, two I2C blocks, five USARTs, four general purpose timers, two basic timers and a 12 channel DMA controller.

The table also gives the flexible static memory controller as not available on the 64 pin high density row, so the external memory bus and the 8080 and 6800 parallel display interface that the feature list mentions need the 100 or 144 pin body. A 384 Kbyte array with no external bus is fine for code, but a frame buffer is not.

The two DAC channels are the reason this part exists in this body. They settle in about 10 microseconds into a 50 pF load, which covers setpoint and offset trimming in a control loop that would otherwise need two external converters on the SPI bus.

Stop current on the high density tables is 24.5 uA typical and 365 uA maximum at 85 C from 3.3 V, which is roughly double the medium density figure. A battery product that budgets from the typical number will be short by an order of magnitude at the top of the range.

The same detector is on this part, with eight levels from 2.08 V to 2.88 V nominal, and it can raise an interrupt rather than only a reset. On a part with two DAC channels that interrupt is what drives the outputs to a safe level before the rail collapses, which matters when the analog output feeds a valve driver or a bias network.

Where this order code fits

It is the 384 Kbyte high density part in a 64 pin body, used where the code is large and two analog outputs are needed but a 100 pin board is not. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Can I connect external SRAM? Not on this package. The flexible static memory controller is absent from the 64 pin high density row, so external memory requires the 100 pin part, where only bank 1 and bank 2 are available, or the 144 pin part with the full controller.

Do both DAC channels come out on 64 pins? Yes. Two 12 bit channels with output buffers are listed for the 64 pin high density row, which is unusual for this pin count and is the main reason to pick it.

How many USARTs does it carry? Five, against three on the medium density line and two on the low density line, and they support ISO 7816, LIN, IrDA and modem control.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the ADC DAC Cross Reference page sets out the checks that keep a substitute from failing on the bench.

Two fields sit after the base code: TR for tape and reel and xxx for a programmed part, and a purchase order that omits both is a tray order. The technical check on this body is the missing external bus, because a 384 Kbyte array with no memory controller means a product that grows a display or an external RAM device has to change package rather than add a part. The two DAC channels do not solve that, since they settle in about 10 microseconds and are analog outputs, not a memory interface, and the 12 channel DMA controller moves data between the peripherals and the 48 Kbytes of internal SRAM only.