Contact Us

STM32F101RCT6

Brand: ST
ST STM32F101RCT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101RCT6 — MCU & Embedded Processors | Superb Automation

STM32F101RCT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101RCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101RCT6: 256 Kbyte, LQFP64 body

STM32F101RCT6 is a member of the STM32F101 high density access line described by DocID14610 Rev 9. The order code fixes 256 Kbytes of Flash, 32 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101RCT6
Program Flash256 Kbytes
SRAM32 Kbytes
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllernot present on the 64 pin body
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersfour 16 bit general purpose timers with up to four compare channels each, two 16 bit basic timers that drive the DAC, plus the independent and window watchdogs and the SysTick counter
Serial interfacesfive USARTs, three SPI blocks and two I2C blocks
DMA12 channel DMA controller
ADC12 bit, 1 microsecond conversion, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Stop current24.5 uA typical and 365 uA maximum at 85 C from a 3.3 V supply
Standby current1.9 uA typical with the low speed oscillator and RTC off, 2.8 uA with them on and 5 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurance10 kcycles, 30 years of retention at 85 C after one kcycle and 20 years at 55 C after 10 kcycles
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

R is 64 pins and C is 256 Kbytes of Flash. DocID14610 gives 32 Kbytes of SRAM, 51 general purpose I/O, 16 converter channels, two 12 bit DAC channels, three SPI blocks, two I2C blocks, five USARTs, four general purpose timers, two basic timers and 12 DMA channels for this row.

The flexible static memory controller is listed as not available on the 64 pin high density part, so the LCD parallel interface in 8080 and 6800 modes also needs a larger body. A 256 Kbyte array without an external bus suits code and data tables, not a framebuffer.

SRAM steps to 32 Kbytes here from 16 Kbytes on the medium density 64 pin part, which is the difference between a single buffer and a queue of buffers for a bus that arrives in bursts. The 12 channel DMA controller is what moves those buffers without stalling the core.

Stop current is 24.5 uA typical and 365 uA maximum at 85 C on 3.3 V, and standby is 1.9 uA typical with the RTC off. Both are larger than the medium density equivalents, so an always on product that moves up a density has to redo its power budget.

The backup domain keeps the RTC, the backup registers and the tamper input alive from VBAT with the main rail off. On a 256 Kbyte part the backup registers are small compared with the Flash, so they hold flags and a time stamp rather than data, and the RTC is calibrated from the 32 kHz oscillator input.

Where this order code fits

It is the 256 Kbyte entry point into the high density line in a 64 pin body, the part that brings two DAC channels and five USARTs into a small board. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What does the 256 Kbyte part add over a 128 Kbyte medium density part? Twice the Flash, twice the SRAM, a 12 channel DMA controller against 7, five USARTs against three, three SPI blocks against two and two 12 bit DAC channels that the medium density line does not have.

Can it drive a parallel display? Not in this package. The 8080 and 6800 interface is carried by the flexible static memory controller, which the 64 pin high density row does not have. The 144 pin body is the one with the full controller.

How many ADC channels are usable? 16, all of them, because the 64 pin body bonds out the full converter.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.

Packing comes from the options field of the ordering scheme, TR for tape and reel and xxx for a programmed part, and the plain code is a tray device. The figure that separates this part from the 48 pin CBT6 in the same memory class is the 16 extra I/O, which is what a board needs when it has to keep the analogue inputs and still bring out a bus, a keypad and a status connector at the same time. The 12 channel DMA controller is the other difference, because the medium density line carries 7 channels and a board that streams the converter, a NAND device and two serial links at once runs out of channels before it runs out of pins.