Contact Us

STM32F101R6T6

Brand: ST
ST STM32F101R6T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101R6T6 — MCU & Embedded Processors | Superb Automation

STM32F101R6T6

ST — MCU & Embedded Processors

Product Overview

The STM32F101R6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101R6T6: 32 Kbyte, LQFP64 body

STM32F101R6T6 is a member of the STM32F101 low density access line described by DocID15058 Rev 6. The order code fixes 32 Kbytes of Flash, 6 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101R6T6
Program Flash32 Kbytes
SRAM6 Kbytes
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timerstwo 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacestwo USARTs, one SPI and one I2C
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 pins
DACnot present on this line
Stop current11.7 uA typical and 145 uA maximum at 85 C from a 3.3 V supply
Standby current2.4 uA typical with the low speed internal oscillator running and 3.2 uA with it off
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

R is 64 pins, 6 is 32 Kbytes of Flash, T is LQFP and 6 is the industrial range. Table 2 of DocID15058 puts the 64 pin low density row at 6 Kbytes of SRAM, 51 general purpose I/O, 16 converter channels, two USARTs, one SPI and one I2C, with two general purpose timers at a 36 MHz ceiling.

This is the cheapest way to get 16 analog inputs and 51 I/O, because the peripheral set stays at the low density level: one SPI and one I2C only. A board that needs a second serial bus has to move to the medium density 64 pin part, which adds a third USART and a second SPI and I2C block.

The 6 Kbytes of SRAM is the limiting term for a 16 channel scan. At 100 kSamples per second across 16 channels the memory fills at 1.6 Kbytes per millisecond, so a 2 Kbyte ring buffer covers 1.2 ms, and logging to an external memory is the normal answer.

Because this code has no A suffix, its electrical reference is the medium density datasheet rather than the low density one, so the stop current to plan against is 14 uA typical and 180 uA maximum at 85 C, not the 11.7 uA figure printed in the low density tables.

The detector thresholds run from 2.08 V to 2.88 V nominal in eight steps, with about 100 mV of hysteresis between the rising and falling edges. On a board that scans 16 channels the warning is what stops the converter cleanly, because an interrupted scan leaves the last sample in the DMA buffer and the application has no way to tell it apart from a real reading.

Where this order code fits

It pairs the 64 pin body and all 16 converter channels with the small 32 Kbyte array, which is what a sensor board with many analog inputs and modest code needs. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Why choose 32 Kbytes with 64 pins? Because the analog input count follows the package. A 64 pin body bonds out all 16 converter channels and 51 I/O for a few cents more than the 48 pin part, which is the right trade when the code is small and the sensor count is high.

How many timers does it have? Two 16 bit general purpose timers, each with up to four compare channels, plus the independent watchdog, the window watchdog and the SysTick counter. There is no advanced control timer on this line.

Is the part 5 V tolerant on every pin? The feature list says almost all I/O are 5 V tolerant, so a few pins are not. The pin definition table in DocID15058 marks the exceptions, and the analog supply and reference pins are outside that statement.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the ADC DAC Cross Reference page sets out the checks that keep a substitute from failing on the bench.

The ordering scheme ends with an options field, TR for tape and reel and xxx for a programmed part, so the base code alone names a tray device. On this part the figure to confirm before ordering is the converter channel map: 16 channels are available, but they are shared with port pins, and a 64 pin board that uses the upper port bits for a bus loses the analogue inputs on those pins. The supply has to stay inside 2.0 to 3.6 V as well, since a 5 V tolerant input is a logic level on a pin and not a permitted rail, and the detector thresholds for an early warning run from 2.08 V to 2.88 V nominal.