Contact Us

STM32F101CBT6

Brand: ST
ST STM32F101CBT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101CBT6 — MCU & Embedded Processors | Superb Automation

STM32F101CBT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101CBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101CBT6: 128 Kbyte, LQFP48 body

STM32F101CBT6 is a member of the STM32F101 medium density access line described by DocID13586 Rev 17. The order code fixes 128 Kbytes of Flash, 16 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101CBT6
Program Flash128 Kbytes
SRAM16 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersthree 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacesthree USARTs, two SPI blocks and two I2C blocks on 48 pins and above, two USARTs, one SPI and one I2C on the 36 pin body
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 and 100 pins
DACnot present on this line
Stop current14 uA typical and 180 uA maximum at 85 C from a 3.3 V supply
Standby current2 uA typical and 4 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

C is 48 pins, B is 128 Kbytes of Flash, T is LQFP and 6 is the industrial range. On the 48 pin medium density row DocID13586 gives 16 Kbytes of SRAM, 37 general purpose I/O, 10 converter channels, three USARTs, two SPI and two I2C blocks, with 36 MHz and 2.0 to 3.6 V.

16 Kbytes of SRAM with 128 Kbytes of Flash is the pairing that makes a small protocol stack practical: a TCP stack, a 4 Kbyte receive buffer and a 2 Kbyte transmit buffer still leave half the memory for application data, which is not the case on the 10 Kbyte parts.

The converter stops at 10 channels in this body even though the array is the largest in the medium density line, so a board that needs 16 analog inputs and 128 Kbytes of code has to take the 64 pin RBT6 instead. Channel count follows pins, not memory.

The 48 pin LQFP is rated 55 C/W, which allows 364 mW of dissipation inside the 20 C junction margin at 85 C ambient. A core running at 36 MHz with two SPI buses active takes a small share of that, so the I/O load is again the term to calculate.

Serial wire debug and JTAG are both present, with the trace port on the same pins. On a 48 pin body the five JTAG pins compete with the second SPI and the third USART, so most boards keep only the two wire debug port and recover the rest through the option bytes once production starts.

Where this order code fits

It is the 128 Kbyte, 48 pin medium density part, the largest array that fits the small body without moving to a 64 pin footprint. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is 128 Kbytes the top of the medium density line? Yes. The next step up is the high density line at 256 Kbytes, which brings a 12 channel DMA controller, five USARTs, three SPI blocks and two DAC channels, together with a larger package.

How many converter channels in this body? 10 of the 16 available. The remaining six are bonded out only on the 64 pin and 100 pin bodies.

Does it support the CRC unit and unique ID? Both are listed for the medium density line, and the 96 bit unique ID is normally used to derive a device serial number or a key.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.

Packing is a separate field in the ordering scheme: TR is tape and reel, xxx is a programmed part, and the plain code is a tray device. The other check on a 128 Kbyte part in a 48 pin body is code size against the 10 converter channels, because the largest array in the medium density line still stops at 10 analogue inputs here, and an application that needs 16 has to take the 64 pin RBT6. SRAM is 16 Kbytes, which is enough for a communication stack plus buffers but not for a framebuffer, and there is no external memory controller on this line to hold one.