Contact Us

STM32F101C8T6

Brand: ST
ST STM32F101C8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101C8T6 — MCU & Embedded Processors | Superb Automation

STM32F101C8T6

ST — MCU & Embedded Processors

Product Overview

The STM32F101C8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101C8T6: 64 Kbyte, LQFP48 body

STM32F101C8T6 is a member of the STM32F101 medium density access line described by DocID13586 Rev 17. The order code fixes 64 Kbytes of Flash, 10 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101C8T6
Program Flash64 Kbytes
SRAM10 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersthree 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacesthree USARTs, two SPI blocks and two I2C blocks on 48 pins and above, two USARTs, one SPI and one I2C on the 36 pin body
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 and 100 pins
DACnot present on this line
Stop current14 uA typical and 180 uA maximum at 85 C from a 3.3 V supply
Standby current2 uA typical and 4 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

C is 48 pins, 8 is 64 Kbytes of Flash, T is LQFP and 6 is minus 40 to plus 85 C, and A would be the internal code that is absent here. On the 48 pin medium density row DocID13586 lists 10 Kbytes of SRAM, 37 general purpose I/O, 10 converter channels, three USARTs, two SPI and two I2C blocks.

Two SPI blocks in a 48 pin body is the feature that keeps this part on so many boards, because a display and a memory device can share the bus without an external multiplexer. The 48 pin low density parts carry one SPI only, so a move between the two lines changes the peripheral count and not just the memory size.

10 Kbytes of SRAM against 37 I/O is a balanced pairing for a control board: a 12 bit converter stream at 100 kSamples per second takes 200 bytes per millisecond, so a 2 Kbyte ring buffer covers 10 ms of history without touching the rest of the memory.

The 48 pin LQFP is rated 55 C/W. With 85 C ambient and a 105 C junction limit the total dissipation allowed is 364 mW, and a board that drives opto couplers or a transistor bridge from the I/O will reach that ceiling before the core does.

The 8 MHz internal oscillator is within 1.1 percent at 25 C and 2.2 percent over the temperature range, which is 176 kHz at the limit. A UART at 115200 baud tolerates about 2 percent of total error once the receiver is counted, so the internal RC is only safe for short links, and a 4 to 16 MHz crystal is the answer when the port has to work over the full range.

Where this order code fits

It is the 64 Kbyte medium density part in a 48 pin body, the most common footprint on small control boards that need two SPI blocks but not a 64 pin package. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is this the same die as STM32F101C6T6? No. This is the medium density device with 64 Kbytes of Flash and 10 Kbytes of SRAM, while the C6T6 is the low density device with 32 Kbytes and 6 Kbytes. The peripheral count also differs inside the same package.

How many USARTs are available? Three on the medium density 48 pin row, against two on the low density 48 pin parts. One of them carries ISO 7816, LIN and IrDA modes.

Can it drive an external memory bus? No. The flexible static memory controller appears on the high density and XL density lines only, so external memory on this part has to sit on SPI or I2C.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the ADC DAC Cross Reference page sets out the checks that keep a substitute from failing on the bench.

On a 48 pin body the options field of the ordering scheme decides two things a buyer sees: TR for tape and reel and xxx for a programmed part, neither of which is part of the base code. The pin budget is the other thing to confirm, since the 37 I/O are shared with two SPI blocks, two I2C blocks and three USARTs, and a harness that uses all three USARTs leaves only a few pins for the application. The 10 converter channels in this body are also shared with those port pins, so an application that needs 16 analogue inputs has to move to the 64 pin part rather than add an external multiplexer.