Contact Us

STM32F101C6T6

Brand: ST
ST STM32F101C6T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101C6T6 — MCU & Embedded Processors | Superb Automation

STM32F101C6T6

ST — MCU & Embedded Processors

Product Overview

The STM32F101C6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101C6T6: 32 Kbyte, LQFP48 body

STM32F101C6T6 is a member of the STM32F101 low density access line described by DocID15058 Rev 6. The order code fixes 32 Kbytes of Flash, 6 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101C6T6
Program Flash32 Kbytes
SRAM6 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timerstwo 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacestwo USARTs, one SPI and one I2C
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 pins
DACnot present on this line
Stop current11.7 uA typical and 145 uA maximum at 85 C from a 3.3 V supply
Standby current2.4 uA typical with the low speed internal oscillator running and 3.2 uA with it off
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

C is 48 pins, 6 is 32 Kbytes of Flash, T is LQFP and 6 is minus 40 to plus 85 C. On the low density 48 pin row DocID15058 gives 6 Kbytes of SRAM, 37 general purpose I/O, 10 converter channels, two USARTs, one SPI and one I2C, and the core runs at up to 36 MHz with single cycle multiply and divide.

Like the 16 Kbyte code, this one has no A suffix, so Table 3 note 1 sends the electrical reference to the medium density STM32F101x8/B datasheet. A substitution file that lists the low density stop current of 11.7 uA typical should be corrected to the medium density figure of 14 uA typical and 180 uA maximum at 85 C, because that is the table the part is guaranteed against.

The step from 16 to 32 Kbytes doubles the program array but moves SRAM only from 4 to 6 Kbytes, and the peripherals do not change at all. Two timers, one SPI and one I2C remain the ceiling, so a board that grows a second serial port has to move to a 64 pin medium density part rather than stay in this body.

With 6 Kbytes of SRAM the usable buffer space after the stack is around 3 Kbytes once a 1 Kbyte stack and a double buffer for the converter are taken out. That is enough for a Modbus or a simple command parser, and it is the reason this part is usually paired with an external EEPROM for calibration data.

Brownout detection matters more on a 32 Kbyte part because there is more state to lose: the detector has eight levels from 2.08 V to 2.88 V nominal with about 100 mV between the rising and falling edges of each, and its interrupt is what starts an emergency save. Below the 2.0 V minimum the part is outside its guaranteed range, and the reset circuit rather than the firmware is what protects the Flash.

Where this order code fits

It is the 32 Kbyte member of the low density line in a 48 pin body, the part chosen when 16 Kbytes of code is not enough but a 64 pin footprint cannot be fitted. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How much SRAM is left for buffers? 6 Kbytes in total on the 32 Kbyte part against 4 Kbytes on the 16 Kbyte part. After a 1 Kbyte stack and a double buffer for the converter, about 3 Kbytes remain, which is why calibration tables usually go to an external EEPROM.

Can I add a second SPI or I2C? Not in this body. The 36 and 48 pin low density parts carry one SPI and one I2C, and the second block only appears on the 64 pin part and on the medium density 48 pin row. A bit banged second port on GPIO is the only route inside this package.

Is the 32 Kbyte low density part still in production? The datasheets in ds358 are marked as production data. What did change is the medium density document, whose revision 9 removed the 32 Kbyte devices from that family, so a distributor listing that calls a 32 Kbyte unit medium density is describing the wrong document.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.