Contact Us

STM32F101C4T6A

Brand: ST
ST STM32F101C4T6A is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101C4T6A — MCU & Embedded Processors | Superb Automation

STM32F101C4T6A

ST — MCU & Embedded Processors

Product Overview

The STM32F101C4T6A from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101C4T6A: 16 Kbyte, LQFP48 body

STM32F101C4T6A is a member of the STM32F101 low density access line described by DocID15058 Rev 6. The order code fixes 16 Kbytes of Flash, 4 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101C4T6A
Program Flash16 Kbytes
SRAM4 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timerstwo 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacestwo USARTs, one SPI and one I2C
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 pins
DACnot present on this line
Stop current11.7 uA typical and 145 uA maximum at 85 C from a 3.3 V supply
Standby current2.4 uA typical with the low speed internal oscillator running and 3.2 uA with it off
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The A after the temperature code is the internal code that Table 3 of DocID15058 treats as a separate row, and note 1 says the orderable numbers without that code fall back to the medium density datasheet. This part is therefore the one whose stop current, wake up time and converter accuracy come from the low density tables, and a drawing that quotes 11.7 uA typical and 145 uA maximum at 85 C is quoting this code.

Everything that is visible on a board is unchanged from the plain code: 48 pins in a 7 x 7 mm LQFP, 16 Kbytes of Flash, 4 Kbytes of SRAM, 37 general purpose I/O, 10 converter channels, two USARTs, one SPI and one I2C. That is exactly the case where a purchasing system will treat the two codes as interchangeable and the qualification file will not.

The A code appears in the low density document at revision 6 and the code letter has been in and out of ordering schemes across the family, so the safest read is to quote the full string including the A on every purchase order and to state which document the incoming inspection plan follows.

16 Kbytes with 4 Kbytes of SRAM leaves about 2 Kbytes for buffers after the stack, which is the smallest working set in the family. The converter is 12 bit with 10 channels in this body, so a board that needs 16 channels has to take the 64 pin part before any code is written.

The backup domain runs from VBAT and keeps the RTC and the backup registers alive while the main rail is off, which is how a 16 Kbyte part remembers a time stamp across a power cut. Tamper detection sits on the same domain and the 32 kHz oscillator with calibration is the clock the RTC counts. A board that leaves VBAT floating loses the time and the tamper flag on every power cycle.

Where this order code fits

It is the A coded 16 Kbyte part, the version that the low density datasheet actually describes, so it is the one to quote when a drawing was qualified against DocID15058. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Can the A code be substituted for the non A code? On a board, yes: the pin out, memory and package are the same. In a qualification file, no: the electrical reference for the non A code is the medium density datasheet, so the stop current and accuracy limits stated in the report differ.

Why does the 48 pin part have 10 converter channels? The 48 pin body brings out 10 of the 16 channels the converter has. The remaining six appear only on the 64 pin part, so channel count follows the package and not the Flash size.

Does the part have a unique ID and a CRC unit? Yes. Both are listed in the feature set of the low density document, and the 96 bit unique ID is what a serial number or a licence key is normally built from.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.