Contact Us

STM32F101C4T6

Brand: ST
ST STM32F101C4T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101C4T6 — MCU & Embedded Processors | Superb Automation

STM32F101C4T6

ST — MCU & Embedded Processors

Product Overview

The STM32F101C4T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101C4T6: 16 Kbyte, LQFP48 body

STM32F101C4T6 is a member of the STM32F101 low density access line described by DocID15058 Rev 6. The order code fixes 16 Kbytes of Flash, 4 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101C4T6
Program Flash16 Kbytes
SRAM4 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timerstwo 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacestwo USARTs, one SPI and one I2C
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 pins
DACnot present on this line
Stop current11.7 uA typical and 145 uA maximum at 85 C from a 3.3 V supply
Standby current2.4 uA typical with the low speed internal oscillator running and 3.2 uA with it off
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The code decodes through the ordering scheme: C is the 48 pin LQFP at 7 x 7 mm, 4 is 16 Kbytes of Flash, T is the LQFP body and 6 is the industrial range of minus 40 to plus 85 C. Table 2 of DocID15058 puts the 48 pin low density row at 4 Kbytes of SRAM, 37 general purpose I/O, 10 channels of the 12 bit converter, two USARTs, one SPI and one I2C, with a 36 MHz ceiling.

This order code carries no A suffix. Table 3 note 1 of the same document says that orderable numbers without the A internal code take their electrical reference from the STM32F101x8/B medium density datasheet, so the low density stop current of 11.7 uA typical and 145 uA maximum at 85 C describes the A code and this part is judged against the medium density tables. The pin out and the memory map are the same, so one board runs both, but a qualification report has to name the document it was written against.

16 Kbytes of Flash and 4 Kbytes of SRAM is the tightest pairing in the family. With the 7 channel DMA controller, two general purpose timers and no USB block, the part suits firmware that already fits in a smaller 8 bit device. A bootloader plus a protocol stack plus a calibration table is where the 4 Kbytes run out first, and the stack has to sit inside that same 4 Kbytes.

The LQFP48 body is rated 55 C/W junction to ambient, so the 20 C the grade allows between 85 C ambient and 105 C junction works out at 364 mW of total dissipation. That budget includes I/O sink current, which is where a board driving LEDs or a relay driver loses its margin before the core does.

The programmable voltage detector gives eight thresholds between 2.08 V and 2.88 V nominal, each with a rising edge about 100 mV above its falling edge. On this part the detector is the only early warning above the 2.0 V floor of the supply range, so a routine that parks the converter outputs and writes a checksum has to finish in the gap between the selected threshold and that floor.

Where this order code fits

It is the 16 Kbyte, 48 pin entry point into the access line, used on sensor nodes and small drives that need 32 bit math and a 12 bit converter but have no room for a bigger body. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is STM32F101C4T6 the same part as STM32F101C4T6A? No. The A is an internal code that Table 3 of DocID15058 separates: the A code is the low density device described by that datasheet, while the code without A takes its electrical reference from the medium density STM32F101x8/B document. Memory, pin count and package are identical, so both run on the same board, but the numbers behind a qualification report are not interchangeable.

Does this part have USB? No. The STM32F101 line carries no USB peripheral at any density. USB full speed is the STM32F102 line with the same pin out on 48 and 64 pins, or the STM32F103 line where the converter and timer count are also higher.

Can it run from a 5 V supply? No. The operating range is 2.0 to 3.6 V. Almost all inputs are 5 V tolerant, which is a logic level on a pin and not permission to power the part from 5 V, so a 5 V system still needs a 3.3 V regulator in front.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.