Contact Us

STM32F100VDT6

Brand: ST
ST STM32F100VDT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F100VDT6 — MCU & Embedded Processors | Superb Automation

STM32F100VDT6

ST — MCU & Embedded Processors

Product Overview

The STM32F100VDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F100VDT6: 384 Kbyte, LQFP100 body

STM32F100VDT6 is a member of the STM32F100 value line high density described by DS5944 Rev 11. The order code fixes 384 Kbytes of Flash, 32 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F100VDT6
Program Flash384 Kbytes
SRAM32 Kbytes
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O80
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllerflexible static memory controller, bank 1 only on this body, multiplexed NOR and PSRAM
Supply voltage2.0 to 3.6 V
Maximum CPU clock24 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS5944 Rev 11

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal on the high speed oscillator
Timersone advanced-control 16 bit timer with four channels and complementary outputs, ten general-purpose 16 bit timers and two basic timers, which with the two watchdogs is the sixteen the cover counts
Serial interfacesthree SPI blocks, two I2C blocks, three USARTs and two UARTs, plus one HDMI CEC channel
DMA12 channel DMA across two controllers
ADC12 bit successive approximation, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Programmable voltage detectoreight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainVBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C
Thermal resistance junction to ambient40 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

384 Kbytes of Flash with 32 Kbytes of SRAM is the pairing that makes a parallel bus worth having. The flexible static memory controller on this 100 pin body supports bank 1 only, and bank 1 on the LQFP100 package is limited to a multiplexed NOR or PSRAM device, so the bus is there for a display controller or a PSRAM and not for a general purpose SRAM array. That limitation is in the footnote of Table 2 of DS5944 Rev 11 and it is the single most important line for a board that plans an external bus.

The high density peripheral set is much wider than the low and medium density one: three SPI blocks, two I2C blocks, three USARTs and two UARTs, one HDMI CEC channel, one advanced-control timer, ten general purpose 16 bit timers and two basic timers. That is sixteen timers once the two watchdogs are counted, which is why this part suits equipment that has to generate several independent PWM channels and still keep a timebase and an encoder interface.

The two UARTs are worth separating from the three USARTs. A UART has no synchronous mode and no smartcard or IrDA support, so it is the right block for a simple asynchronous link to a host or a radio module, while the USARTs handle the ports that need the extra modes. On a part with five asynchronous ports in total, that distinction is what stops a board from running out of a feature it assumed was present everywhere.

At 40 C/W on the LQFP100 body the junction rises 20 C above an 85 C ambient at about 500 mW, which is the best thermal figure in this package family. A board with 80 general purpose I/O driving a display bus and several outputs is the case where that matters, because the bus pins toggle at the access rate and the I/O current is a real part of the dissipation. The 100 pin body has the copper area to spread it, provided the pad is connected into a plane.

The converter has 16 channels and the two 12 bit DAC channels are buffered. On a part with an external memory bus the analog side needs care: the bus is a source of fast edges, and the reference pin, the analog supply pins and the converter inputs all sit in the same package. Keeping the analog pins on the side of the package away from the bus and giving each supply pin its own capacitor is the practical measure, and it is cheaper than selecting a part with a better converter.

Flash endurance is 10 kcycles at minus 40 to plus 85 C, with 30 years of retention at 85 C after one kcycle and 10 years at 105 C. On a 384 Kbyte part with an external memory controller, the parameter store often lives in the external device rather than in the program Flash, which protects the endurance budget and keeps the image free for code. The backup domain from VBAT holds the RTC, the backup registers and the tamper input either way.

The value line core runs at 24 MHz, which with 32 Kbytes of SRAM and an external bus makes this part a controller rather than a signal processor. A display refresh, a keypad scan, three serial protocols and a control loop fit inside 24 MHz if the work is interrupt driven and the copies are done by the 12 channel DMA. Work that needs a 48 or 72 MHz core is the STM32F103 line, which has a different pin out and a different memory map.

Where this order code fits

It is the 384 Kbyte value line part with the external memory controller, used where the application needs 32 Kbytes of SRAM and a parallel display or memory bus on a 100 pin board. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What can be connected to the external memory controller on the 100 pin body? Bank 1 only, and only a multiplexed NOR or PSRAM device on the LQFP100 package. Bank 2 and the additional chip selects exist on the 144 pin body. A board that needs a NAND device or two independent chip selects has to move to the larger package.

Does this part have USB? No. The value line and the access line have no USB peripheral. USB full speed is the STM32F102 line, and the STM32F103 line adds USB together with a 72 MHz core, but neither is a drop in replacement for this pin out.

How much SRAM does the 384 Kbyte code have? 32 Kbytes, which is the top of the range in this family along with the 512 Kbyte code. The 256 Kbyte codes have 24 Kbytes and the low and medium density parts have 4 or 8 Kbytes, so the step in SRAM is a step in device class rather than a small increment.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.