STM32F100RCT6
Product Specifications
STM32F100RCT6
ST — MCU & Embedded Processors
Product Overview
The STM32F100RCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F100RCT6: 256 Kbyte, LQFP64 body
STM32F100RCT6 is a member of the STM32F100 value line high density described by DS5944 Rev 11. The order code fixes 256 Kbytes of Flash, 24 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.
Order code and memory
| Order code | STM32F100RCT6 |
| Program Flash | 256 Kbytes |
| SRAM | 24 Kbytes |
| Package | LQFP64, 10 x 10 mm, 64 pins |
| Maximum general purpose I/O | 51 |
| Analog input channels | 16 of the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| External memory controller | not present on this body, bank 1 only on the 100 pin body of the same family |
| Supply voltage | 2.0 to 3.6 V |
| Maximum CPU clock | 24 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DS5944 Rev 11 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide |
| Clock sources | 8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal on the high speed oscillator |
| Timers | one advanced-control 16 bit timer with four channels and complementary outputs, ten general-purpose 16 bit timers and two basic timers, which with the two watchdogs is the sixteen the cover counts |
| Serial interfaces | three SPI blocks, two I2C blocks, three USARTs and two UARTs, plus one HDMI CEC channel |
| DMA | 12 channel DMA across two controllers |
| ADC | 12 bit successive approximation, 16 channels, conversion range 0 to 3.6 V |
| DAC | 2 channels of 12 bits with output buffers |
| Programmable voltage detector | eight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | VBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C |
| Thermal resistance junction to ambient | 49 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant |
| USB | not present, USB full speed is the STM32F102 line |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
This is the high density silicon in a 10 x 10 mm body, and the external memory controller is absent on the 64 pin package even though the same family has it on 100 and 144 pins. Table 2 of DS5944 Rev 11 marks the row as No for the 64 pin column, which means a board that later needs a parallel display has to change package and not just add a connector. Deciding that early is cheaper than discovering it at the second prototype.
The 24 Kbytes of SRAM is three times what the medium density parts offer and it changes what the firmware can do. A 128 by 64 monochrome frame buffer is 1 Kbyte, a double buffered converter scan over 16 channels is a few hundred bytes, and three serial ports with 512 byte buffers is 1.5 Kbytes, all of which now fits with room for a look up table and a stack. This is the memory size where a small graphics display stops needing its own controller memory.
The interface count is the high density set even in 64 pins: three SPI blocks, two I2C blocks, three USARTs and two UARTs, plus CEC. On a 64 pin body those cannot all be brought out at once, because the alternate functions share port A, B, C and D pins. The pin table is the document that decides which five asynchronous ports, which three SPI blocks and which two I2C blocks are available together, and it is worth reading before the connector is fixed rather than after.
Ten general purpose timers plus one advanced-control timer and two basic timers is a lot of timing for a 64 pin part. A three phase inverter uses the advanced timer for the bridge, one general purpose timer for the current loop, one for the encoder or Hall input and one for the timebase, and still leaves six for PWM channels, input capture and a stepper. That headroom is the reason this part turns up in multi axis motion controllers.
At 49 C/W on the LQFP64 body the junction rises 20 C above an 85 C ambient at about 410 mW, which is slightly less thermal room than the 100 pin package offers for the same silicon. In a motion controller the part often sits near gate drivers, so the ambient inside the enclosure is above the room temperature and the derating has to start from the measured figure. Vias under the exposed pad into a ground plane are the cheapest way to buy margin.
Flash endurance is 10 kcycles at minus 40 to plus 85 C, with 30 years of retention at 85 C after one kcycle. On a 256 Kbyte part the option to keep two application slots is real: 128 Kbytes each is enough for a control application with a bootloader, and the swap can be done by writing the second slot and changing a pointer. That arrangement writes the Flash far more than a parameter store does, so the endurance budget belongs in the engineering notes.
The core ceiling of 24 MHz is the limit that separates this part from the STM32F103 performance line. A control application that runs a current loop at 16 kHz with a three phase modulation fits; a motor control application that also runs a field oriented observer in floating point at 16 kHz does not. Moving to the F103 line means a different pin out for the same 64 pins, so it is a board change and not a substitution.
Where this order code fits
It is the 256 Kbyte high density code in the 64 pin body, used where the image and the SRAM are the reason for the part and a parallel bus is not needed. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Does the 64 pin high density code have the external memory controller? No. The controller exists on the 100 and 144 pin bodies of this family. On the 64 pin package the pins are not there, so the row in Table 2 reads No and the board cannot add a parallel bus later without changing package.
How many asynchronous serial ports are there? Five in total, made up of three USARTs and two UARTs. How many can be brought out at once on a 64 pin body depends on which other alternate functions are in use, and the pin table is the document that answers it for a specific combination.
Is 24 Kbytes of SRAM enough for a small display? For a monochrome panel with a kilobyte or two of buffer, yes, with room for the rest of the application. For a colour panel at 320 by 240 with 16 bits per pixel the frame buffer alone is 150 Kbytes, which is outside this part and outside the whole value line.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.