Contact Us

STM32F100R8T6

Brand: ST
ST STM32F100R8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F100R8T6 — MCU & Embedded Processors | Superb Automation

STM32F100R8T6

ST — MCU & Embedded Processors

Product Overview

The STM32F100R8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F100R8T6: 64 Kbyte, LQFP64 body

STM32F100R8T6 is a member of the STM32F100 value line low and medium density described by DocID16455 Rev 9. The order code fixes 64 Kbytes of Flash, 8 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F100R8T6
Program Flash64 Kbytes
SRAM8 Kbytes
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllernot present on this body
Supply voltage2.0 to 3.6 V
Maximum CPU clock24 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDocID16455 Rev 9

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal range 4 to 24 MHz
Timersone advanced-control 16 bit timer with four channels and complementary outputs with dead time, up to six general-purpose 16 bit timers with four compare channels each, and two basic timers that trigger the converter
Serial interfacesup to two SPI blocks, two I2C blocks and three USARTs, plus one HDMI CEC channel
DMA7 channel DMA controller
ADC12 bit successive approximation, 1 microsecond conversion, 10 channels on 48 pins and 16 channels on 64 and 100 pins
DAC2 channels of 12 bits with output buffers
Programmable voltage detectoreight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainVBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C
Thermal resistance junction to ambient45 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

This is the first memory size on the line that brings the complete medium density interface set to a 64 pin body: two SPI blocks, two I2C blocks, three USARTs, the HDMI CEC channel, one advanced-control timer, up to six general purpose 16 bit timers, two basic timers and the two 12 bit DAC channels. The 16 and 32 Kbyte codes in the same package have one SPI, one I2C and two USARTs, so a board that grows from 32 to 64 Kbytes gains interfaces rather than only memory.

The 8 Kbytes of SRAM is what makes three simultaneous serial ports practical. A 512 byte buffer per port is 1.5 Kbytes, the converter scan with a double buffer and its descriptors is a few hundred bytes, and the stack for a Cortex-M3 running a control loop with fixed point maths fits in the rest. The 7 channel DMA controller lets the ports and the converter move data without the core copying, which is how a 24 MHz part keeps three ports fed.

Sixteen converter channels plus two DAC channels on one body is the analog budget, and it is generous for a part at this clock rate. Three phase current, a bus voltage, a board thermistor and a potentiometer use five channels; the DAC pair can drive a fan setpoint and a contrast or bias voltage. The remaining channels are what a second sensor group or a redundant measurement uses, and the internal temperature sensor occupies one more.

The advanced-control timer with complementary outputs and dead time is the reason to use this part on a motor drive rather than a general purpose timer alone. It produces the three complementary pairs for a six step bridge with a dead time that the hardware inserts, so the gate driver sees the same gap regardless of interrupt latency. The general purpose timers then handle the speed loop, the Hall or encoder input and the timebase, and the two basic timers pace the converter and the DAC.

At 45 C/W on the LQFP64 body the junction sits 20 C above an 85 C ambient at roughly 440 mW of total dissipation. In a motor drive the part often sits next to the gate driver and the shunt resistors, so the ambient is not the enclosure temperature and the copper under the package is part of the answer. Spreading the ground pad into a plane and keeping the analog supply pin away from the switching node is worth more than any package change.

Flash endurance of 10 kcycles at minus 40 to plus 85 C and 30 years of retention at 85 C after one kcycle is the figure for firmware that stores parameters. A drive that saves a parameter set on every change is well inside it; a drive that logs position every 100 ms is not, and on this part the backup registers kept alive from VBAT or an external EEPROM on the I2C block are the alternatives. The option bytes and the read out protection are set at the same time, so the plan for both should be written before the first production run.

The internal oscillator is within 1.1 percent at 25 C and 2.2 percent over temperature, and the PLL multiplies it to the 24 MHz core clock. Three USARTs at high baud, a converter that has to be precise about its sample rate and a timer that paces the control loop all argue for a crystal, and the external oscillator accepts 4 to 24 MHz. The two pins the crystal takes are part of the 51 I/O on this body, which is the trade to record on the pin list.

Where this order code fits

It is the 64 Kbyte, 64 pin code that most control boards settle on: full medium density interfaces, 16 converter channels and 8 Kbytes of SRAM in a 10 x 10 mm body. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the BOM Shortage Recovery page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How does this code differ from the 128 Kbyte code in the same package? Only the Flash and the SRAM: 64 Kbytes with 8 Kbytes here against 128 Kbytes with 8 Kbytes there. The package, the pin count, the 51 general purpose I/O, the 16 converter channels, the two DAC channels and the full medium density interface set are identical.

Does the 24 MHz core clock limit a motor control loop? It sets the loop period. At 24 MHz a control loop of 20 microseconds of code runs at 50 kHz at best and realistically well below that once the converter and the serial handling are added, which is enough for a six step drive and for field oriented control at modest electrical frequencies.

Can the part run from the internal oscillator in a product? Yes for the converter, the timers and a single serial port at moderate baud. For three simultaneously active ports, or where the sample rate has to be accurate over temperature, a crystal is the safer choice because the internal RC moves by 2.2 percent across the range.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.