STM32F100C6T6
Product Specifications
STM32F100C6T6
ST — MCU & Embedded Processors
Product Overview
The STM32F100C6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F100C6T6: 32 Kbyte, LQFP48 body
STM32F100C6T6 is a member of the STM32F100 value line low and medium density described by DocID16455 Rev 9. The order code fixes 32 Kbytes of Flash, 4 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.
Order code and memory
| Order code | STM32F100C6T6 |
| Program Flash | 32 Kbytes |
| SRAM | 4 Kbytes |
| Package | LQFP48, 7 x 7 mm, 48 pins |
| Maximum general purpose I/O | 37 |
| Analog input channels | 10 of the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| External memory controller | not present on this body |
| Supply voltage | 2.0 to 3.6 V |
| Maximum CPU clock | 24 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DocID16455 Rev 9 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide |
| Clock sources | 8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal range 4 to 24 MHz |
| Timers | one advanced-control 16 bit timer with four channels and complementary outputs with dead time, up to six general-purpose 16 bit timers with four compare channels each, and two basic timers that trigger the converter |
| Serial interfaces | up to two SPI blocks, two I2C blocks and three USARTs, plus one HDMI CEC channel |
| DMA | 7 channel DMA controller |
| ADC | 12 bit successive approximation, 1 microsecond conversion, 10 channels on 48 pins and 16 channels on 64 and 100 pins |
| DAC | 2 channels of 12 bits with output buffers |
| Programmable voltage detector | eight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | VBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C |
| Thermal resistance junction to ambient | 55 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant |
| USB | not present, USB full speed is the STM32F102 line |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
This code carries no internal letter after the temperature digit, which is the difference between it and the B marked version of the same memory size. Memory, package, pin count and converter channels are identical, and the same datasheet covers both, but the two strings are separate orderable parts. A production line that mixes them without a deviation is mixing two die revisions under one part number, and a qualification file that records only one of them will not describe what is on the board.
The peripheral set is the low density set: on 48 pins the 16 and 32 Kbyte codes bring one SPI block, one I2C block and two of the three USARTs, while the 64 and 128 Kbyte codes in the same body bring the full medium density set. That is the single most common surprise on this line, because the package is identical and only the memory column of Table 2 changes. Reading the table by memory size rather than by package is what prevents a board revision that loses an interface.
The 4 Kbytes of SRAM and 32 Kbytes of Flash pair is the tightest in the family. A 1 Kbyte stack, a 256 byte receive buffer per active port and a calibration table leave very little for a heap, which is why firmware on this part is normally written without dynamic allocation. The 7 channel DMA controller helps, because a stream moves samples without the application spending stack on a handler.
The two 12 bit DAC channels are the feature that separates the value line from the access line at this memory size, and they are buffered, so they can drive a load directly without an external op amp on the output. The trade is that the outputs share pins with converter inputs, which means a board using both converters loses two analog channels out of the 10 available on a 48 pin body. Counting the analog pins before fixing the connector is the check that catches this.
The voltage detector has eight levels and can raise an interrupt rather than only reset the part. On a 32 Kbyte code with a DAC, that interrupt is the natural place to drive the analog outputs to a defined level before the rail collapses, because a converter output that floats during a brownout is worse than one that is parked. The thresholds run from 2.00 V to 2.88 V falling, with about 100 mV between the falling and rising edges of each level.
Serial wire debug needs two pins and JTAG needs five, and on a 37 I/O body that is a real share of the port. The pins return to the application when the debug port is disabled in the option bytes, which is how a production board recovers them, but the recovery is one way on a sealed unit: a field return that needs a debugger then has no entry point unless a test pad was left on the two wire port.
The timer set includes one advanced-control timer with complementary outputs and dead time, which is enough for a three phase bridge in six step mode without external logic. The dead time is inserted by the timer itself, so the gate driver sees a fixed gap rather than one that depends on interrupt latency, and that is the reason to spend the advanced timer on the power stage and leave the general purpose timers for the control loop and the timebase.
Where this order code fits
It is the plain 32 Kbyte code without the trailing internal letter, used where a board was qualified against the earlier revision and the B marked part cannot simply be swapped in without a paperwork change. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the BOM Shortage Recovery page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Is this part the same as STM32F100C6T6B? Electrically the same memory size and the same pin out, but the two strings are different orderable parts and the trailing letter is an internal code. A substitution between them is a revision change that should be recorded, and a board file should name one of the two strings rather than the family.
How many serial interfaces are available on 48 pins at 32 Kbytes? One SPI block, one I2C block and two USARTs, plus the HDMI CEC channel. The third USART and the second SPI and I2C blocks appear on this body only at 64 Kbytes and above, which is a memory column decision rather than a package decision.
Why does a value line part have a DAC? Because the value line is aimed at appliance and motor control boards that need a setpoint or a bias voltage without an external converter. The two channels are 12 bit and buffered, and they draw about 0.5 mA of analog supply current when enabled, which has to be added to the rail budget.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.