Contact Us

MAX25302BATD/V+T

Brand: Analog Devices
Analog Devices MAX25302BATD/V+T is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX25302BATD/V+T — Analog & Mixed-Signal ICs | Superb Automation

MAX25302BATD/V+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX25302BATD/V+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

MAX25302BATD/V+T: A 2 A Automotive LDO Whose Rating Is Thermal Long Before It Is Electrical

The MAX25302BATD/V+T is the adjustable member of a two-part 2 A low noise regulator family: the MAX25302A selects one of nine output voltages with two pins at power-up, and the MAX25302B sets its output with an external divider from a 0.6 V reference, which is the version on this page. The input range is 1.7 V to 5.5 V, the output range is 0.6 V to 5.0 V, the output noise is 5.1 uV rms from 10 Hz to 100 kHz, and the dropout is 100 mV maximum at 2 A, 65 mV typical. The part is AEC-Q100 qualified over minus 40 to plus 125 degrees in a 14-pin TDFN measuring 3 mm by 3.5 mm, and that package is where the conversation about 2 A actually happens.

2 A of current in a 3 mm by 3.5 mm body

A linear regulator dissipates the product of the current and the input to output difference, so 2 A from 3.3 V to 1.8 V is 3 W and 2 A from 5 V to 1.8 V is 6.4 W. Neither figure is available from a 14-pin TDFN in still air, whatever the current limit says. The 2 A number is a silicon and package current capability that is reached only when the voltage across the pass device is small, which in practice means a rail to rail conversion such as 1.8 V to 1.2 V at 2 A, where the dissipation is 1.2 W, or a 2.5 V to 1.8 V conversion at a lower current. The dropping resistor trick does not apply to an LDO, so the honest way to use this part is as a post regulator after a switching stage, with the input set only slightly above the output.

The reference, the divider and the tolerance that follows

The feedback threshold is 0.6 V with plus or minus 1 percent accuracy over load, line and temperature, which is 0.594 V to 0.606 V. A 1.8 V output therefore needs a divider ratio of 2 to 1, and a 3.3 V output needs 4.5 to 1. The divider's own resistors add a tolerance term that the regulator cannot remove, so a pair of 1 percent resistors adds roughly 1.4 percent in the worst case before the reference is counted, and a pair of 0.1 percent resistors costs more than the regulator to save it. This matters because the adjustable version is often chosen for an output voltage that the fixed version does not offer, and the divider then becomes the accuracy limit of the rail.

ParameterValue on this order codeWhat it decides
Input range1.7 V to 5.5 VA 1.8 V rail can be made from a 2.5 V rail
Output range0.6 V to 5.0 V, set by two resistorsThe B version, the A version has nine fixed values
Output current2 A maximumThermally limited well before 2 A in most sockets
Dropout65 mV typical, 100 mV maximum at 2 ALow enough for a post regulator
Output noise5.1 uV rms, 10 Hz to 100 kHzNeeds no ferrite bead for most converter rails
Supply rejectionMore than 70 dB at 10 kHzSwitching ripple from the upstream stage is attenuated
Quiescent current1.3 mA, shutdown 0.04 uA typicalCosts 6.5 mW at 5 V, not a battery part
Output capacitor8 uF minimum, 22 uF typicalCeramic only, the value is stability not ripple
QualificationAEC-Q100, minus 40 to plus 125 degreesThe V suffix on the order code

Power-OK, soft start and the sequencing question

The B version carries an active high power-OK output that goes high when the output reaches 91 percent of regulation, and it is an open drain pin that needs a pull-up to a supply the host can read. That 91 percent threshold is not the same as in regulation, so a host that waits for it is waiting for a level slightly below the final value, which is fine for sequencing and not fine for a measurement. The soft start rate is set by the bypass capacitor, so the inrush into a large output capacitance is a component choice rather than a fixed behaviour, and a rail that has to come up inside a given window has to size that capacitor against the load capacitance and not from a table.

Where the part fits

Automotive sensor and audio rails, high resolution data acquisition supplies and any post regulation of a switching rail that needs low noise and a defined start-up belong here, and the AEC-Q100 qualification is what makes the automotive sockets possible at all. Where the input to output difference is larger, a switching regulator has to come first, and the ADI part second source page sets out what a substitute regulator has to match, including the bypass capacitor and the power-OK behaviour. The pin to pin cross reference covers the package question and the one stop BOM sourcing page covers the rail parts on one order.