INA125UA/2K5
Product Specifications
INA125UA/2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA125UA/2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA125UA/2K5: Instrumentation amplifier with a precision reference on the same die
INA125UA/2K5 is an instrumentation amplifier in the 16 pin SO body with a 460 uA quiescent current, a 250 uV offset and an on chip reference that delivers 1.24 V, 2.5 V, 5 V or 10 V without a second package in a SOIC-16 body of 16 pins. The INA125 combines a three amplifier instrumentation front end with a precision voltage reference, which is the combination a bridge sensor needs: the bridge is excited by the reference and its output is amplified by the same die, so the measurement is ratiometric by construction. Gain is set by one resistor with the relationship of 4 plus 60 kohm divided by the resistor value, so a 60 kohm resistor gives a gain of 5 and a 600 ohm resistor gives a gain of 104. The inputs survive plus and minus 40 V, the supply range is 2.7 V to 36 V single ended or plus and minus 1.35 V to plus and minus 18 V, and a sleep pin drops the current to a few microamps.
Order code and package
| Order code | INA125UA/2K5 |
| Gain equation | 4 plus 60 kohm divided by the gain resistor |
| Reference voltages | 1.24 V, 2.5 V, 5 V and 10 V |
| Supply, single | 2.7 V to 36 V |
| Supply, dual | plus and minus 1.35 V to plus and minus 18 V |
| Package | 16 pin SOIC, U body |
| Packing | 2500 pieces per reel |
| Document | PDS-1361B, Burr-Brown |
Electrical parameters that decide the application
| Quiescent current | 460 uA |
| Offset voltage | 250 uV maximum |
| Offset drift | 2 uV per degree maximum |
| Input bias current | 20 nA maximum |
| Common mode rejection | 100 dB minimum at a gain of 100 |
| Input noise | 38 nV per root hertz at 1 kHz |
| Input protection | plus and minus 40 V |
| Reference accuracy | plus or minus 0.5 percent maximum |
| Reference drift | plus or minus 35 ppm per degree maximum |
| Bandwidth at a gain of 4 | 150 kHz |
| Sleep mode | provided, controlled by a pin |
Points to check before this part goes on a BOM
The gain resistor follows a law rather than a ratio, so the minimum gain is 4 and every value of resistance adds to it. A 60 kohm resistor gives 5, a 6 kohm resistor gives 14, a 600 ohm resistor gives 104, and an open circuit leaves the amplifier at a gain of 4 with the input stage still connected. That last case is the one to board for: a connector that comes loose, or a resistor that is not fitted, leaves a working amplifier at a gain of 4 rather than an undefined one, and the reading that follows is wrong by a factor of 25 rather than absent.
A 250 uV offset at a gain of 100 is 25 mV at the output, which on a 3.3 V converter is 0.75 percent of the range. The drift of 2 uV per degree is 200 uV at the output over a 40 degree rise, another 0.2 percent of the range at the output but 40 percent of the input signal if that signal is 500 uV. The conclusion for a bridge sensor is that the part works at a gain of 100 for a signal of a few millivolts and not for a signal of hundreds of microvolts, where a zero drift amplifier is the appropriate front end.
The common mode rejection of 100 dB is specified at a gain of 100 and it falls as the gain falls, because the input stage is a pair of buffers whose own rejection is fixed. At a gain of 4 the rejection is lower and the datasheet characteristics show it. A board that uses this part at a low gain for a high level signal is therefore not getting the 100 dB it was chosen for, which is a common mistake when a part is picked from the feature list rather than from the gain it will run at.
The 38 nV per root hertz input noise is 3.8 uV over a 10 kHz bandwidth, which at a gain of 100 is 380 uV at the output, comparable with the offset. Noise and offset are therefore the same order of magnitude in a wideband board, and a narrowband filter on the output reduces the noise term without touching the offset. For a bridge that moves slowly, a 10 Hz bandwidth brings the noise to 120 nV, which is a twentieth of the offset and no longer the limiting term.
The reference is the reason to use this part rather than a separate amplifier. Its accuracy is 0.5 percent and its drift is 35 ppm per degree, and both terms appear in the measurement only to the extent that the bridge is not ratiometric. A resistive bridge excited by the reference produces an output proportional to the excitation, so a drift in the excitation changes the sensitivity, and the same drift applied to the converter reference cancels it. This is why the reference output is usually wired to both the bridge and the analog to digital converter, and why a board that uses a separate converter reference loses the cancellation.
Four hundred and sixty microamps of quiescent current is the specification that puts this part in battery instruments, and it is quoted without the bridge current. A 350 ohm bridge on a 2.5 V excitation draws 7 mA, which is fifteen times the amplifier. The sleep pin therefore saves the amplifier current and leaves the bridge current, unless the excitation is also switched, and switching the excitation changes the settling time of the bridge before the measurement can be taken.
Plus and minus 40 V of input protection is a large claim and it comes with a condition: the input current has to be limited. On a plus and minus 15 V supply the protection diodes conduct at about 40 V, and at that point the current through them is set by the source impedance. A 10 kohm series resistor at 40 V limits the current to 4 mA, which the structure tolerates; a direct connection does not. In a 4 to 20 mA loop the series resistance is already there, which is why the part is common in that application.
Where this order code fits
This order code belongs on pressure and temperature bridge amplifiers, load cells, industrial process transmitters, multi channel data acquisition and battery powered instruments, where the excitation and the amplification have to share a reference so that the supply drift cancels. It is also the part chosen where the input has to survive a wiring fault, because the plus and minus 40 V input protection covers a 24 V industrial loop applied to the wrong terminal. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
What gain can be set with one resistor? From 4 upward, following 4 plus 60 kohm divided by the resistor. A 600 ohm resistor gives about 104, a 60 ohm resistor gives about 1004. The resistor tolerance adds directly to the gain error, so a 1 percent part is the practical choice, and the minimum gain of 4 applies even with the resistor open.
Is the on chip reference accurate enough for a bridge? It is 0.5 percent and 35 ppm per degree, which is adequate for a ratiometric measurement because the same reference feeds the bridge and the converter. For an absolute measurement with a separate converter reference, the 0.5 percent becomes a direct gain error and the choice of a precision external reference is the better route.
How much does the input protection cover? Plus and minus 40 V with the input current limited, which covers a 24 V industrial loop applied in reverse. The limit is the current, not the voltage: the series resistance in the signal path is what makes the rating true, and a direct connection to a low impedance source does not use the protection at all.
Can it run from a single 3.3 V supply? It runs from 2.7 V to 36 V single ended, so 3.3 V is inside the range. What changes is the output swing and the common mode range, both of which shrink toward the lower rail. A bridge with a 1.65 V common mode and a 2.5 V excitation cannot be measured on a 3.3 V supply with this part, because the excitation is above the supply and the output cannot reach it.
SUPERB holds and sources this amplifier line against the exact order code, with the reel, date code and country of origin stated on the offer. When a signal chain has to move to a second part, the BOM Shortage Recovery page sets out the checks that separate a working substitute from one that fails on the bench.