Contact Us

VBP16R90S

Brand: VBsemi
VBsemi VBP16R90S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP16R90S — Discrete & Power Semiconductors | Superb Automation

VBP16R90S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP16R90S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP16R90S: 600 V and 90 A in a TO247 with 24 milliohm

The VBP16R90S is a single N channel MOSFET in a TO247 body, rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 90 A of drain current and 24 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die. It is the largest member of the 600 V family in this catalogue.

Twenty four milliohm at 600 V is the practical floor for a TO247. The die fills the cavity, the wire bonds carry 90 A in parallel, and the package thermal resistance sets the current long before the silicon does. At 90 A the die makes 194 W, at 68 A 111 W, at 45 A 49 W and at 22 A 12 W.

A part like this is bought for a 3 kW stage that has to fit in one switch position, or for a battery charger where the input current is high and the bus is 400 V. It is also bought as a two part parallel bank for a 6 kW stage, where the two parts run cool enough to keep the electrolytic capacitors alive.

Key data for the VBP16R90S

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS600 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID90 A
RDS(on) at 10 V24 milliohm
StructureSuperjunction, multiple epitaxy
Loss at 22 A11.6 W
Loss at 45 A48.6 W
Loss at 68 A111.0 W
Loss at 90 A194.4 W

The package is the limit at 24 milliohm

At 40 A continuous the hot loss is 77 W. A TO247 junction to case at 0.35 K per watt puts the junction 27 C above the case, and the case to heatsink pad adds 0.4 K per watt, so the heatsink sees 1.1 K per watt of the total. With a 0.5 K per watt heatsink at 45 C ambient the junction is at 121 C, which is inside the limit.

At 50 A the hot loss is 120 W and the junction is at 153 C on the same heatsink, which is outside. The step from 40 A to 50 A is the difference between a working board and a field return, and it is only 25 percent of current.

Forced air at 0.2 K per watt moves the 50 A case to 109 C and the junction to 151 C, still marginal. The honest continuous figure for one part is 40 to 45 A with a good fan and 25 A on a plate.

Driving a 24 milliohm die

The gate charge of a die this size is high, in the 100 to 150 nC region for the class. At 100 kHz that is 10 to 15 mA of average gate current, which is small, but the peak during the transition is 2 to 3 A and the driver has to source it without a voltage sag. A 4 A peak driver with a 2.2 ohm resistor is the usual arrangement.

The source inductance matters at these currents. The TO247 source pin carries the full drain current during the on time, and the di/dt at turn off through the source inductance subtracts from the gate drive. A four lead body with a separate source return removes that term, and where the board can take it, the four lead version is the better choice at 40 A and above.

The gate resistor sets the trade between the drain spike and the switching loss. At 400 V and 40 A a 20 ns transition with a 4.7 ohm resistor gives a 2 kV per microsecond dv/dt, which is at the edge of what a standard snubber handles. A 10 ohm resistor halves the dv/dt and adds 3 W of switching loss.

Where this part fits

Power factor stages from 3 to 5 kW, EV chargers at 6.6 kW with a two part bank, server power supplies at 3 kW, and welding inverters at 20 kHz. In a welder the duty is 0.2 to 0.4 and the peak current is 100 A, so the conduction loss at the peak is 240 W for a fraction of the cycle and the average is 50 to 90 W.

In a charger the part runs at 60 to 100 kHz in a boost stage and the switching loss is a third of the total. At 100 kHz the gate charge becomes as important as the resistance, and a smaller die with lower charge can win on total loss.

Where the stage is a bridgeless power factor stage with two switches, the two parts run on alternate half cycles and each carries half the average current. The safety stock planning page covers how a bank of high current parts is held when the build plan is uneven through the year.

The sourcing side of this part is covered on the material requirements planning. For a part that a 3 kW stage depends on, that page covers how demand is carried against the build plan.

Questions we get on this code

Is 40 A continuous realistic? With a fan cooled heatsink at 0.5 K per watt, yes, at a 121 C junction. Without a fan, 25 A is the working figure.

What is the difference from the 90 A SE part? The SE part prints 18 milliohm at the same 90 A and is a deep trench die. Same voltage, same package, lower resistance. The two are not the same die.

Should the four lead body be used instead? Above 40 A and 100 kHz, yes, because the separate source return removes the common source inductance from the gate loop.

How is a mixed lot identified? By the laser marking on the tab side, which carries the date code and the lot. A lot without a readable marking is held at goods inwards rather than released to the line.