VBP16R32S
Product Specifications
VBP16R32S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP16R32S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP16R32S: 600 V and 32 A in a TO247 with 85 milliohm
The VBP16R32S is a single N channel MOSFET in a TO247 body, rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 32 A of drain current and 85 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die. It is the member of the 600 V family that most often appears on a 600 to 800 W power factor stage.
Eighty five milliohm at 600 V is the point where a single TO247 carries 15 A continuously without a fan. At 32 A the die makes 87 W, at 24 A 49 W, at 16 A 22 W and at 8 A 5.4 W. The working current on a plate heatsink is 12 to 14 A, and on a fan cooled heatsink 18 to 22 A.
The 600 V class is chosen on these boards because the reflected voltage of the transformer is fixed at 420 V and the leakage spike at 520 V, so the margin to 600 V is 80 V. Moving to 650 V would be free electrically and would cost a requalification of the surge test.
Key data for the VBP16R32S
| Configuration | Single N channel |
| Package | TO247, through hole, tab on the drain |
| VDS | 600 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 32 A |
| RDS(on) at 10 V | 85 milliohm |
| Structure | Superjunction, multiple epitaxy |
| Loss at 8 A | 5.4 W |
| Loss at 16 A | 21.8 W |
| Loss at 24 A | 49.0 W |
| Loss at 32 A | 87.0 W |
What the resistance buys at 800 W
At 800 W from a 400 V bus the input current is 2 A average and 5.7 A peak. At 85 milliohm the conduction loss at the peak is 2.8 W and the root mean square over the line cycle is 2.6 A giving 0.6 W. Switching at 400 V and 5.7 A with a 25 ns crossover is 2.3 W peak and 1.0 W averaged. Total 1.6 W cold, near 3 W hot.
A TO247 at 3 W on a plate heatsink with 2 K per watt sits 6 C above ambient, which is nothing. The part could carry twice the current on the same heatsink, and the limit is the peak current during a startup or a surge rather than the steady state.
That is the reason the 32 A member is often chosen for a stage that only needs 15 A. The thermal margin absorbs the startup surge and the line brownout ride through, and the extra die area is cheaper than a bigger heatsink.
Surge and startup behaviour
A boost stage at 800 W draws 12 A during a startup inrush for 10 ms while the output capacitor charges. At 85 milliohm the loss during that interval is 12 W, and the die temperature rises by only a few degrees because the thermal time constant of the die is milliseconds and the package is seconds.
The limiting case is a short circuit on the output, where a current limit holds the switch in linear mode for as long as the controller allows. That is where the safe operating area matters, and the vendor page does not print one. A controller with a 10 microsecond limit is safe for any part in this class, and a controller with a 1 ms limit is not.
Repeated startup at 10 per minute is still comfortable. The average loss added by startup is 12 W times 10 ms times 10 per minute, which is 0.02 W averaged, and the junction does not see it.
Where this part fits
Power factor stages from 600 W to 1 kW, LLC and forward converters at 400 V, telecom rectifiers, and the primary of a 700 W charger. In a two switch forward the two parts share the off state voltage and the clamp diodes recover the leakage, so the 600 V rating is comfortable on a 400 V bus.
In a bridge the body diode recovery has to be checked at the switching frequency. A standard superjunction body diode at 16 A and 100 kHz puts a recovery spike on the opposite switch that adds 2 to 4 W, and a fast recovery grade removes most of it.
For a board that runs at 40 to 60 kHz in a sealed box, this part at 12 A is inside its thermal budget without a fan. At 100 kHz the switching term grows and the 24 milliohm member of the family becomes the better total loss.
The diode on the boost path sets the turn on loss of this switch. A silicon carbide boost diode at 650 V has almost no recovered charge and the switch turns on into a clean node. A fast silicon diode at the same voltage carries 30 to 60 nC of recovered charge, which is dumped through the switch at every turn on and shows up as a 2 to 4 W term at 60 kHz. That is larger than the difference between two neighbouring members of the family, so the diode is the part to fix first.
The sourcing side of this part is covered on the component lead time solutions. For a 600 V part bought in volume, that page covers how the lead time is planned rather than discovered.
Questions we get on this code
Is the 4.5 V column available? No, the vendor prints the 10 V resistance only. A 5 V drive on a 3.5 V threshold part leaves little overdrive, so drive at 10 V and the printed figure applies.
Can it be used on a 400 V three phase line? No. That bus rectifies to 565 V and a regenerating load takes it above 600 V. The class for that line is 900 V or 1200 V.
What is the body diode forward drop? Not printed. For a bridge, measure it on a sample, because the dead time loss depends on it and a superjunction body diode is around 1.2 to 1.5 V at 10 A.
Which grade is the second source? Any 600 V superjunction part at 85 milliohm in TO247 with the same gate threshold class. The strategic sourcing page covers how that second source is held rather than bought at the last minute.