Contact Us

VBTA1220N

Brand: VBsemi
VBsemi VBTA1220N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBTA1220N — Discrete & Power Semiconductors | Superb Automation

VBTA1220N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBTA1220N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBTA1220N: a 20 V N channel in the SC-75 body

The VBTA1220N is a single N channel in the SC-75 three lead body, printed at 20 V, 270 milliohm at a 4.5 V gate and 390 milliohm at 2.5 V, 0.85 A at a 25 C case, 6 A pulsed, 1.4 nC of gate charge and 105 pF of input capacitance. The data sheet names smart phones and tablet PCs, DC to DC converters, boost converters, load switches and OVP switches. It is the smallest part in this bank and it is bought for a signal path rather than for power.

At 270 milliohm and 0.85 A the part dissipates 0.2 W at its rated current, and the junction to ambient resistance of 250 K per watt typical means that is a 50 C rise. That number is the whole story of the SC-75 body: the package is a signal package, and the current rating is set by what the three leads can pass rather than by the die. The die itself would carry more if it were mounted on something with a thermal path.

The 1.4 nC gate charge is what makes the part useful. At 1 MHz the drive is 1.4 mA, at 3 MHz 4.2 mA, so a controller output can switch it at frequencies where the passive parts around it are the size of the part itself. This is the class of part used to switch a small rail in a phone, where the whole converter occupies 4 square millimetres.

Key data for the VBTA1220N

ConfigurationSingle N channel
PackageSC-75, three lead
VDS20 V
RDS(on) at 4.5 V270 milliohm at 0.85 A
RDS(on) at 2.5 V390 milliohm at 0.70 A
ID at a 25 C case0.85 A, 0.70 A on the reduced drive column
Pulsed drain current6 A at 300 microsecond
Ciss105 pF
Gate charge1.4 nC typical
Body diode0.8 V typical at 1.1 A, 1.2 V maximum
RthJA250 K per watt typical, 300 maximum at 10 s
RthJF225 K per watt typical, 270 maximum
ApplicationsSmart phones and tablets, DC to DC, boost, load switch, OVP switch
FeaturesTrench die, 100 per cent gate resistance tested

The difference between the 4.5 V and 2.5 V columns is 44 per cent, which is large in ratio and small in absolute terms, 120 milliohm. On a 0.5 A load that is 60 mV of drop, and on a phone rail with a 3 per cent tolerance at 1.8 V that is 2 per cent of the budget. This is why the part is chosen with the lowest gate drive the circuit can provide rather than the highest.

The junction to foot resistance of 225 K per watt is only marginally better than the junction to ambient figure, which says the three leads are the limit and the board cannot help much. On a part like this the copper under the body is 1 millimetre square and the thermal path is the lead frame, so the only way to carry more current is to use a bigger body rather than a better board.

Where a 20 V part in an SC-75 is used

The first case is a load switch for a peripheral rail in a phone, such as the supply to a camera module or a sensor hub. The current is 100 to 300 mA, the 270 milliohm gives 27 to 81 mV of drop, and the 1.4 nC gate charge lets the rail be sequenced at any speed the controller chooses. The part is chosen for size and for the low gate charge, not for the current.

The second case is a boost converter for a small display bias at 20 to 40 V from a 3.7 V pack. Here the switch carries the inductor current, which is 200 to 500 mA, and the 20 V rating limits the boost ratio to about four. A higher output needs a higher voltage part, and this one is bought for a bias rail rather than for a main rail.

The third case is an OVP switch, where the part sits between a USB connector and the system and is turned off when the input exceeds 5.5 V. The response time is set by the gate charge and the driver, and 1.4 nC allows the part to be turned off in a few hundred nanoseconds, which is fast enough to protect the system from a 12 V charger plugged into a 5 V port.

Switching small currents fast

At 105 pF of input capacitance and 1.4 nC of gate charge the part can be driven from a microcontroller pin through a 100 ohm resistor with a 140 ns time constant. That is fast enough that the drain ringing, not the gate, becomes the limit, and on a 20 V part fed from 5 V the ringing is small because the currents are small.

The body diode drop of 0.8 V at 1.1 A is significant compared with the channel drop of 0.3 V at the same current. In a boost converter that means the dead time matters: the diode conducts for the whole dead time, and 0.8 V at 0.5 A is 0.4 W in a body that can dissipate 0.2 W. The dead time has to be short, and the controller has to be able to blank the ringing that follows.

Where the same rail is bought across several products, the how to reduce component cost page covers where the money actually sits in a small converter, and on a part at this price the placement cost is usually larger than the part cost. In this band the practical move is to use one code across several rails rather than to chase a cent on the device.

What to check before this code is bought

The current rating of 0.85 A is a case figure at 25 C. At 250 K per watt junction to ambient, a 60 C enclosure allows 0.36 W, which at 270 milliohm is 1.1 A, so the current is not the limit and the voltage drop is. Any circuit that needs more than 1 A from this body needs a different package rather than a lower resistance.

The sheet does not print a threshold value in the rows we read, only a dash in the threshold cell of the extract. That is a gap in the text rather than in the part, but it means the drive requirement cannot be confirmed from the sheet and should be asked for. A part specified at 2.5 V is comfortable on a 4.5 V drive and marginal on a 3.3 V one.

Where the code is compared with other parts in the same three lead body, the power management cross reference page sets out which parameters have to match before a substitute is proposed, from threshold and gate charge to the body diode direction. In an SC-75 body the pin out is the same across vendors, so the swap usually works and the gate charge is what changes the switching loss.

The packing is a tape of 3 mm pitch, and the SC-75 body is small enough that a reel can hold 3000 parts. A reel that has been opened and left in a warm room takes up moisture, and the part is reflowed at 260 C peak, so the moisture level and the bake rule matter more here than on a larger body.

Questions we get on this code

Can it carry 1 A continuously? In a 25 C room, yes, at 270 mV of drop. In a 60 C enclosure the practical figure is 0.8 A, and at 1 A the part is at 0.27 W against a 0.36 W allowance, before any margin.

Is the gate drive 4.5 V or 2.5 V? The sheet prints both columns, 270 milliohm and 390 milliohm. On a 3.3 V rail the part sits between them, and without a threshold figure on the sheet we would not quote an interpolated number.

Can it be used in a boost converter at 12 V output? Yes, from a 3.7 V pack, with a switch current of a few hundred milliamps. Above about 16 V output the 20 V rating leaves no room for the ringing at the switch node.

Why is the thermal resistance so high? Because the SC-75 body has three small leads and no pad. 250 K per watt is a property of the package, and it is the reason this part is bought for signal currents rather than for power.