Contact Us

VBQG7322

Brand: VBsemi
VBsemi VBQG7322 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG7322 — Discrete & Power Semiconductors | Superb Automation

VBQG7322

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG7322 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG7322: a 30 V N channel in a 2 by 2 SC-70 leadless body

The VBQG7322 is a single N channel in the 2.05 mm square SC-70 six lead leadless body, printed at 30 V, 23 milliohm at a 10 V gate and 27 milliohm at 4.5 V, 6 A at a 25 C case and 5 A on the reduced drive column, with a 4.2 nC gate charge, 424 pF of input capacitance and a threshold window of 1.2 to 2.5 V. The data sheet names DC to DC converters and high speed switching. It is the switching element for a small converter where the board area per switch is measured in millimetres.

The body has no exposed pad in the usual sense: the six leads and the drain bars underneath carry the heat, which is why the junction to ambient resistance is 75 K per watt typical against 39 for the DFN 2 by 2 parts in this catalogue. That single number explains the whole application window. A part at 27 milliohm carrying 2 A dissipates 0.11 W, and 75 K per watt gives an 8 C rise, which is fine. The same part at 4 A dissipates 0.43 W and rises 32 C, which is also fine until the ambient is 60 C.

The low gate charge is the point of the part. At 4.2 nC the drive current at 1 MHz is 4.2 mA and at 2 MHz 8.4 mA, so a small controller can switch it at frequencies where the inductor and the output capacitance shrink enough to fit the same small area. A part with 15 nC in the same body would be limited to a third of that frequency for the same driver.

Key data for the VBQG7322

ConfigurationSingle N channel
PackageSC-70 six lead, leadless, 2.05 mm square
VDS30 V
Vth1.2 to 2.5 V at 250 microamp
RDS(on) at 10 V23 milliohm at 6 A
RDS(on) at 4.5 V27 milliohm at 5 A
ID at a 25 C case6 A, 5 A on the reduced drive column
Pulsed drain current25 A at 300 microsecond
Ciss424 pF
Gate charge4.2 nC typical
Body diode0.82 V typical at the rated current, 1.2 V maximum
RthJA75 K per watt typical, 100 maximum at 5 s
RthJF40 K per watt typical, 50 maximum
ApplicationsDC to DC converters, high speed switching
ComplianceHalogen free to IEC 61249-2-21, RoHS

The threshold window of 1.2 to 2.5 V is the widest in this small body family, and it has two consequences. The good one is that the part is not turned on by noise on a 3.3 V gate when the driver is in a high impedance state, because 2.5 V is close to the rail. The bad one is that a part at the top of the window needs 4 V of gate to be fully enhanced, so a 3.3 V logic drive leaves some units only partly on and the resistance is not the 27 milliohm printed for 4.5 V.

The junction to foot resistance of 40 K per watt typical tells the buyer what the six leads can do. With a drain bar soldered to 25 square millimetres of copper the part runs at about 40 K per watt, and with the minimum footprint it runs at 75. The difference is a factor of nearly two on the current an engineer can draw, so a footprint decision made early sets the current rating of the whole converter.

Where a 30 V part with 4.2 nC is used

The first case is the switching stage of a step down converter from 12 V to 1.2 V at 3 to 5 A in a module the size of a fingernail. The low gate charge allows 1 to 2 MHz, which keeps the inductor at 1 microhenry and the output capacitance at 22 microfarad. The 6 A case current is above the 5 A the converter delivers, and the junction to ambient of 75 K per watt is what keeps the part inside its rating at 5 A.

The second case is a synchronous rectifier in the same converter. Here the part conducts for most of the cycle at low duty, and the body diode carries the current during the dead time. The 0.82 V drop is high compared with a dedicated rectifier, so the dead time is kept short and the controller has to blank the comparator for the ringing that follows.

The third case is a high side switch for a small load, such as a sensor rail or a radio module supply. The 30 V rating covers a 12 V rail with a transient, and 27 milliohm at 4.5 V gives a 27 mV drop at 1 A, which is below the tolerance of most rails. The part is chosen here for its size rather than its current.

Drive, ringing and the leadless body

At 4.2 nC the gate resistor can be small, 2 to 5 ohm, and the edge is fast enough that the drain ringing becomes the limiting feature. On a 30 V part fed from 12 V, the ringing at the switch node can reach twice the input voltage with a poor board, so a snubber or a slower gate is needed to keep the peak under 30 V. This is the same trade as on the DFN parts, but with less thermal margin to absorb a bad choice.

The 424 pF input capacitance is small enough that two parts in parallel can be driven from one controller output, giving 13.5 milliohm at 8.4 nC, which is often the cheapest way to a lower resistance when the area is already committed. The limit is the ringing of two drains in parallel rather than the drive current.

Where a part in this body is being swapped for another vendor's code in the same footprint, the how to verify a drop in replacement page sets out the bench checks, from threshold and gate charge to the body diode direction, that decide whether the substitute behaves the same in the circuit. The six lead leadless body is common, but the drain bar pattern differs between vendors, so the land pattern has to be checked rather than assumed.

What to check before this code is bought

The leadless body has no exposed pad in the usual sense and the solder joint is made on the drain bars underneath. That joint cannot be inspected from the side, and the only control is the paste stencil and the reflow profile. A part that is placed with a 0.1 mm offset still works and still fails the thermal test later, which is the failure mode seen most often on this outline.

The threshold window is wide enough to matter on a 3.3 V rail. Ask for the threshold distribution before committing to a 3.3 V gate drive, or use a 5 V driver, which puts the whole window above the knee. A mixed lot with two threshold populations will show up as units that run hot at light load.

Where the code is compared with other N channels in the same footprint, the power management cross reference page sets out which parameters have to match before a substitute is proposed, from threshold and gate charge to the avalanche rating. This sheet prints no avalanche rating at all, which is worth noting: a converter that relies on the switch to absorb the leakage energy of a transformer has no published limit on this part.

The reel and the tape pocket are the other practical check. The 2.05 mm square body sits in an 8 mm tape, and the pocket depth has to match the 0.8 mm height. A shallow pocket leaves the part riding high and the nozzle will place it off centre, which shows up as a solder void on one drain bar.

Questions we get on this code

Can it be driven from 3.3 V logic? Sometimes. The threshold reaches 2.5 V at the top of the window, so a 3.3 V gate leaves 0.8 V of overdrive on the worst unit and the resistance is well above 27 milliohm. A 5 V driver removes the question.

Is 6 A the current on a board? Only with the case at 25 C. At 75 K per watt junction to ambient and a 60 C enclosure, 3 A is the practical continuous figure, which is 0.24 W and a 18 C rise.

Why is the junction to ambient so much worse than the DFN 2 by 2? Because the heat leaves through six small leads rather than a 4 square millimetre pad. 75 against 39 K per watt is the whole difference, and it is set by the body rather than by the die.

What happens on a shorted output? The 25 A pulsed rating is a 300 microsecond figure, and a short lasts longer than that. The current limit in the controller is what protects the part, and the gate should be slowed so the part survives the few microseconds before the limit acts.