VBQG2317
Product Specifications
VBQG2317
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQG2317 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQG2317: a minus 30 V P channel with a 22 milliohm channel
The VBQG2317 is a single P channel in the thermally enhanced DFN 2 by 2, printed at minus 30 V, 22 milliohm at a minus 4.5 V gate and 30 milliohm at minus 2.5 V, with a minus 10 A case current, a 0.4 to 1 V threshold window and 18 nC of gate charge. The data sheet names load switch, PA switch and battery switch for portable devices. The 2 by 2 body with an exposed pad is the reason the part can hold a 10 A label at all, since the pad is the only thermal path.
Thirty volts is the class used on a two cell pack at 8.4 V with margin, and also on a 12 V rail where the transients reach 20 V. The resistance at a 4.5 V gate is 22 milliohm, which is among the lowest in this small body at that voltage, and the 30 milliohm at 2.5 V says the part still works on a nearly flat cell, at a price of 36 per cent more resistance.
This part and the minus 20 V member of the family are pin compatible. The choice between them is margin against resistance: the 20 V part is 20 milliohm and the 30 V part is 22 milliohm, so the extra voltage costs two milliohms and nothing else. On a two cell pack the 30 V part is the default because 8.4 V plus the charger overshoot plus the ringing leaves little room under 20 V.
Key data for the VBQG2317
| Configuration | Single P channel |
| Package | Thermally enhanced DFN 2 by 2 |
| VDS | Minus 30 V |
| Vth | Minus 0.4 to minus 1 V at 250 microamp |
| RDS(on) at minus 4.5 V | 22 milliohm |
| RDS(on) at minus 2.5 V | 30 milliohm |
| ID at a 25 C case | Minus 10 A |
| ID on the reduced drive column | Minus 9 A |
| Pulsed drain current | Minus 30 A at 300 microsecond |
| Gate charge | 18 nC typical |
| Body diode | Minus 0.8 V at minus 8 A, 40 ns recovery typical |
| Recovered charge | 20 nC typical, 30 nC maximum |
| RthJA | 28 K per watt typical, 38 maximum at 5 s |
| Junction range | Industrial range on this sheet |
| Applications | Load switch, PA switch, battery switch for portable devices |
The threshold window of minus 0.4 to minus 1 V is wide in ratio but low in absolute terms, which is normal for a P channel. The consequence is that a gate sitting 1 V below the source is not off, and a gate sitting at the source is off only because there is no drive at all. In a battery switch that is opened by a controller, the gate must be pulled up to the source with a resistor, not left floating, or the part will sit in a partly on state and heat without any load current to show for it.
The junction to ambient resistance of 28 K per watt typical in a 2 by 2 is the best number in this family, and it depends entirely on the pad. At 5 A and 22 milliohm the loss is 0.55 W, which against 28 K per watt gives 15 C of rise, and against 60 K per watt, which is what a poorly soldered pad gives, 33 C. In an enclosure at 60 C the first case is comfortable and the second is not, and nothing in the part changed.
Where a minus 30 V P channel is used
The first case is a battery switch on a two cell pack in a portable instrument. The part carries the system current, 2 to 4 A in normal use and up to 8 A in a transmit burst, and the 22 milliohm gives 0.14 W at 8 A. The body diode blocks a reversed pack and the gate is held up by a 100 k resistor so the part is off when the switch is open.
The second case is a PA switch in a handheld radio. The power amplifier is switched off between transmissions to save battery, and the switch has to pass 1 to 2 A at 7.4 V with a low drop. Here the resistance at a 4.5 V gate is the number that matters, because the gate is driven from the battery through a level shift and the drive falls as the pack discharges.
The third case is a 12 V rail load switch in an industrial controller. The 30 V rating covers a 12 V rail with a 20 V transient, and the part is used to isolate a subsystem during a fault. The inrush into the subsystem capacitance sets the gate slew, and a 22 milliohm channel with 18 nC of gate charge gives a turn on of a few milliseconds through a 100 k gate resistor.
Drive, protection and the gate window
The gate is driven to the source for off and to ground for on, and the available drive is the battery voltage. On a 12 V rail the gate sees 12 V, so a part rated for 12 V on the gate is exactly at its limit, and this family is often paired with a 12 V zener from gate to source. On a two cell pack at 8.4 V there is margin, and on a single cell at 4.2 V the drive sits in the 4.5 V column with the resistance at 22 milliohm.
The body diode recovery of 40 ns typical and 20 nC of recovered charge is slow compared with an N channel of the same size, and that is a property of the P channel die. In a circuit where the P channel works against another switch, the recovery spike has to be absorbed by a capacitor or a clamp, and on a 12 V rail with a 30 V part there is room for it.
Where the part is being considered as a second source for a P channel from another vendor, the power management cross reference page sets out which parameters have to match, from the threshold window and the gate charge to the body diode recovery. The resistance at the low gate voltage is the parameter that most often differs between vendors, because the gate oxide thickness changes the 2.5 V column by 30 per cent between otherwise similar parts.
What to check before this code is bought
The sheet does not print a storage and operating range in the rows we read, and the industry default for this body is minus 55 to 150 C. A build that needs a wider range or a specific automotive grade has to ask for the qualification document rather than infer it from the resistance table.
The pulsed current of minus 30 A is a 300 microsecond rating, which is short. A load switch that has to charge 470 microfarad into a shorted output will see a much longer pulse than that, and without a safe operating area curve the gate slew has to be slow enough that the part never reaches the current limit. This is a circuit decision, and a 100 ohm to 1 k gate resistor is the usual tool.
Where the part is carried across two products at different currents, the BOM consolidation page covers how the family is merged onto fewer codes without losing a qualification, and in this band the practical argument is that one 30 V code covers both a two cell pack and a 12 V rail, so the second code buys nothing.
The marking on a 2 by 2 body is small, and the part is delivered on tape whose pocket depth must match the 0.8 mm body. A reel that has been split and rejoined is the most common source of a mixed lot, and on a part with a 28 K per watt thermal path, a different die in the same reel will not show up until the thermal test.
Questions we get on this code
What is the gate voltage limit? The summary block prints a plus or minus 12 V window on this family, so a 12 V rail pulling the gate to ground is at the limit. A zener clamp from gate to source is standard practice here.
Is the 22 milliohm figure at 4.5 V or at 10 V? At 4.5 V. The sheet prints no 10 V column for this part, so there is no lower number to quote, and a 10 V gate does not make the part meaningfully better than 22 milliohm.
Can two of these be paralleled for 20 A? They can, and the resistance halves to 11 milliohm, but the threshold window of 0.4 to 1 V means the two parts share current unevenly until both are fully enhanced. Paralleling P channels with a wide threshold window needs a small source resistor or a matched pair from one lot.
Does the part protect against a reversed battery? The body diode blocks the reverse current when the part is off, so yes for a reversed pack, and the diode drop is the price when the circuit is asked to conduct with the channel off.