Contact Us

VBQF5325

Brand: VBsemi
VBsemi VBQF5325 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF5325 — Discrete & Power Semiconductors | Superb Automation

VBQF5325

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF5325 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF5325: an N channel and a P channel in one 3 by 3 body

The VBQF5325 is a complementary pair in the DFN 3 by 3 body: one 30 V N channel at 13 milliohm on a 10 V gate, 15 on 8 V and 17 on 4.5 V, with 8 A of drain current and 6.2 nC of gate charge, and one 30 V P channel at 40 milliohm on a minus 10 V gate, 42 on minus 8 and 45 on minus 4.5, with minus 6 A and 18.5 nC of gate charge. The P channel is three times the resistance of the N channel because hole mobility is a third of electron mobility at the same die area.

A complementary pair is the standard output stage of a small motor driver or a push pull stage, because the two devices can be driven from one signal with a small dead time. It is also the standard half of a class D amplifier and the standard pass element pair of a linear regulator with a low dropout on one side and a fast turn off on the other. The vendor names motor drive and mobile power bank, and both use the pair as a bidirectional switch or as a synchronous output.

The 30 V rating on both channels is the interesting part: a P channel and an N channel of the same voltage in one body is not common, because the P channel normally needs a larger die for the same resistance and the two are built on different starting material. Having the pair in one 3 by 3 body saves the board area and the matching, and the cost is that the P channel is the weak side at 40 milliohm.

Key data for the VBQF5325

ConfigurationOne N channel and one P channel
PackageDFN 3 by 3, split pads
VDS30 V N channel, minus 30 V P channel
VGSPlus or minus 20 V
Vth1.6 V N channel, minus 1.7 V P channel
RDS(on), N at 10 V13 milliohm
RDS(on), N at 8 V15 milliohm
RDS(on), N at 4.5 V17 milliohm
RDS(on), P at minus 10 V40 milliohm
RDS(on), P at minus 8 V42 milliohm
RDS(on), P at minus 4.5 V45 milliohm
ID8 A N channel, minus 6 A P channel at a 25 C case
Pulsed drain current40 A N channel, minus 20 A P channel
Qg6.2 nC N channel, 18.5 nC P channel
RthJA50 K per watt N, 47 K per watt P, 62.5 maximum
Body diode, N0.81 V typical, 1.2 V maximum

The P channel gate charge of 18.5 nC is three times the N channel figure, and that is the number that decides the driver. If both gates are driven from one signal, the P channel sets the drive current, and at 500 kHz it needs 9.3 mA. The gate to source charge of the P channel also sets the turn off time, which is why a complementary pair in a motor driver switches slower on the high side than on the low side.

The junction to ambient resistance of 50 K per watt on the N channel and 47 on the P channel is high compared with a single device in the same body, because both die heat the same lead frame. At 4 A the N channel dissipates 0.27 W and the P channel at 4 A dissipates 0.72 W, so the pair together is 1 W and the shared pad rises 47 to 50 K. That is the practical limit of the part: 4 A total per leg in still air, 6 A with a plane.

Motor drive and the mobile power bank

In a brushed DC motor driver the pair forms a half bridge with the motor between the switch node and ground, or a full bridge with two of these packages. At 12 V and 3 A the N channel carries the low side current and the P channel the high side, and the P channel at 45 milliohm dissipates 0.4 W. For a 20 W motor that is acceptable, and it avoids the charge pump that an all N channel bridge would need.

In a mobile power bank the pair is used as the bidirectional switch between the cell and the boost converter, with the N channel on the cell side and the P channel on the output side, so that either direction can be blocked by turning both off. The 30 V rating covers a single cell at 4.2 V with a 20 V boost output, and the low threshold of both devices lets the gates be driven from a 3.3 V controller through a small level shift.

The third use is a load switch with a defined off state. The P channel blocks the positive line and the N channel blocks the return, so a fault that raises either line above the rail cannot feed through a body diode. That is the arrangement used where a connector can be back driven, and it costs one extra device compared with a single P channel switch.

Drive and the asymmetry

The two gates need separate drive. The N channel is driven from ground reference and switches in 10 ns; the P channel needs its gate pulled below its source, and with 18.5 nC of charge the pull down has to sink 20 mA for a fast edge. A single open drain output with a 1 k resistor gives a 20 microsecond edge, which is fine for a motor driver and too slow for a converter.

The threshold of the P channel is minus 1.7 V, so a 3.3 V drive is 1.6 V below threshold and the part is only partly on. A 5 V drive gives 3.3 V below threshold and the resistance is close to the 45 milliohm printed for minus 4.5 V. On a 12 V rail with the gate pulled to ground the drive is 12 V and the resistance is the 40 milliohm figure.

Where the pair has to be replaced because the original code has gone short lead, the how to verify a drop in replacement page covers the bench checks, and on a complementary pair the two that matter are the threshold polarity of each channel and the body diode direction, because a mis-ordered pair conducts through both diodes at once.

Buying this code

The vendor states halogen-free construction, RoHS compliance, 100 per cent gate resistance and unclamped inductive switching tests, and no automotive qualification. The complementary pair is a common source of a mixed reel, since the body looks the same as the dual N pair of the same family from above. The reel label and a curve trace on both channels are what separate them.

Where a build carries both this pair and the dual N pair, the incoming inspection plan page covers what is checked on receipt, and the test for a P channel has to reverse the gate polarity, which a plan written for N channels will not do.

The sourcing side of this part is covered on the incoming inspection plan. For a complementary pair that looks identical to the dual N pair from above, that page covers what is checked on receipt.

Questions we get on this code

Why is the P channel three times the resistance? Hole mobility is about a third of electron mobility, so the same die area gives three times the resistance. Matching the two would need a P channel die three times the size.

Can both devices be driven from one pin? Only through a level shift, and the P channel's 18.5 nC sets the drive current. A motor driver at a few kilohertz can do it; a converter at 500 kHz cannot.

Can the pair block current in both directions? Yes when both devices are off, one through the P channel body diode and one through the N channel. That is the reason to use a pair instead of a single switch.

Is 8 A a continuous rating on the N channel? At a 25 C case. In still air the pair is good for 3 to 4 A total, and the 50 K per watt ambient resistance is the number that sets it.