Contact Us

VBQF3316

Brand: VBsemi
VBsemi VBQF3316 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF3316 — Discrete & Power Semiconductors | Superb Automation

VBQF3316

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF3316 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF3316: a dual 30 V pair at 16 milliohm

The VBQF3316 is a dual N channel MOSFET in the DFN 3.3 by 3.3 body, two independent 30 V devices, 16 milliohm at a 10 V gate and 20 milliohm at 4.5 V, 26 A per device, 4.1 nC of gate charge, 480 pF of input capacitance and a 1.7 V threshold. The vendor lists synchronous rectification, notebook system power, point of load and low current DC to DC as the applications, and the low gate charge is the reason it is listed for the switching positions rather than for a load switch.

The pair is a different proposition from the 8 milliohm dual in the same family. Twice the resistance buys a quarter of the gate charge, and in a converter that runs at 1 to 2 MHz the gate charge is the loss that matters. At 1 MHz, 8.4 nC costs 8.4 mA of drive and 4.1 nC costs 4.1 mA, and the switching loss in the driver falls with it. The crossover between the two parts is around 8 to 10 A per device.

The body is 3.3 mm square with the pads split, and the die are mounted side by side. The junction to ambient resistance is published as a single figure for the pair, so the two losses add on one thermal path. In a buck converter that is a fair approximation because the two devices conduct at different times, but in a two rail system where both are on continuously the pair runs hotter than either would alone.

Key data for the VBQF3316

ConfigurationDual N channel, independent
PackageDFN 3.3 by 3.3, split pads
VDS30 V per device
VGSPlus or minus 20 V
Vth1.7 V typical
RDS(on) at 10 V16 milliohm
RDS(on) at 4.5 V20 milliohm
ID at a 25 C case26 A per device
ID at a 25 C ambient8.8 A per device
Pulsed drain current80 A
Qg4.1 nC typical
Qgs and Qgd1.5 nC and 1.3 nC
Ciss480 pF
Body diode0.8 V typical, 1.2 V maximum
Power at a 25 C case23 W per device
Avalanche14 A, 9.8 mJ at 0.1 mH

The current rows show the whole thermal story in one column: 26 A at a 25 C case, 21 A at a 70 C case, 8.8 A at a 25 C ambient and 7 A at a 70 C ambient. The case figures assume the pad is held there by a heatsink or a plane; the ambient figures assume a 1 inch square board. For a converter that has to work in a 60 C enclosure, 7 A per device is the number, and a 15 A phase needs both devices but not at the same time.

The threshold of 1.7 V with 4.1 nC of gate charge is a deliberate pairing: a low threshold lets the part reach 20 milliohm at 4.5 V, and a small gate keeps the drive loss low. The price is a leakage that rises with temperature, and the drain leakage row at 150 C is worth reading on any circuit that holds the part off across a battery for months.

Point of load and low current DC to DC

A 12 V to 1.8 V point of load converter at 2 MHz and 6 A per phase is the natural home for this pair. The high side conducts for 15 per cent of the period at 6 A and 20 milliohm, 0.1 W, and the low side for the rest at 0.4 W. The switching loss at 2 MHz with 4.1 nC and a 12 V rail is about 0.3 W, so the split is 0.1, 0.4 and 0.3, and the pair runs at a 60 K rise on a four square centimetre pad.

At 12 A per phase the same pair is at 1.6 W on the low side and the rise doubles. That is the point to move to the 8 milliohm dual or to a two phase arrangement, and the decision is made on the conduction loss rather than on the headline current, because the headline is a case figure at 25 C.

The low current DC to DC application on the vendor page is the same circuit at 1 to 3 A, where the pair is chosen for the small body and the low gate charge rather than for the current. At 2 A the conduction loss is 0.08 W and the switching loss dominates, so a part with half the gate charge would be better even at twice the resistance.

Drive, dead time and the board

The 1.5 nC of gate to source charge is a third of the total, which means the Miller plateau is short and the part switches in 10 to 15 ns with a 1 A driver. That is fast enough to ring, and a 4.7 to 10 ohm gate resistor per device is the usual damping. The two gates are separate pins, so each device needs its own resistor even when one driver output feeds both.

The split pads mean the land pattern has to keep the two drains apart. A pour that touches both turns the pair into a single 8 milliohm device with the two gates in parallel, which works until one die fails short and takes the other with it. The 3.3 mm body has 0.65 mm of pitch on the lead side, so a 0.15 mm solder mask dam between the pads is what keeps the two nets separate after reflow.

Where a board qualified on the 8 milliohm dual has to move to this pair, the pin to pin cross reference page covers which parameters have to match before the swap, and on a dual the gate charge and the threshold matter more than the resistance, because the drive and the dead time were tuned around them.

Buying this code

The vendor states halogen-free construction to IEC 61249-2-21, RoHS compliance to the 2002/95 directive, and 100 per cent gate resistance and unclamped inductive switching tests. There is no automotive qualification on the page. The 9.8 mJ avalanche energy at 0.1 mH is a real single pulse rating and it is useful in a converter that sees an inductive kick on a long output cable.

Where the same pair is carried across several point of load rails at different currents, the BOM consolidation page covers how the family is merged onto fewer codes without losing a qualification, which usually saves more than the price difference between adjacent members.

The gate resistors are the part of this circuit that gets left out. With two devices in one body, a single resistor from the driver to both gates couples the two gate loops, and the device that switches first pulls the other gate through the Miller capacitance. Two resistors of 4.7 ohm, one per gate, with a short return to the driver source, is what keeps the pair switching together and keeps the dead time where the driver set it.

The sourcing side of this part is covered on the BOM consolidation. For the pair carried across several point of load rails, that page covers how the family is merged onto fewer codes.

Questions we get on this code

Are 26 A and 8.8 A the same rating? No. The first is a case figure at 25 C and the second an ambient figure on a one inch board. The ambient figure is the one a converter in an enclosure has to meet.

Can the two devices be used in parallel instead of as a pair? Yes, with a separate gate resistor on each. The shared thermal path means the pair runs hotter than two single parts at the same total loss.

Is 20 milliohm the number at a 5 V gate? It is the number at 4.5 V. At 5 V the resistance is slightly lower and the data sheet curve is the place to read it.

What is the 9.8 mJ avalanche figure for? A single pulse into 0.1 mH at 14 A. It is not a repetitive rating, and a converter that rings every cycle needs a snubber rather than an avalanche budget.