VBQF3307
Product Specifications
VBQF3307
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF3307 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF3307: a dual 30 V pair built for the high side
The VBQF3307 is a dual N channel MOSFET in the DFN 3 by 3 body, two independent 30 V devices in one package, 8 milliohm at a 10 V gate and 13 milliohm at 4.5 V, 30 A per device, 8.4 nC of gate charge, a 2.0 V threshold and a junction to ambient resistance of 39 K per watt typical and 53 maximum in the steady state. The vendor describes the pair as optimized for high side synchronous rectifier operation, which on a notebook CPU core means the smaller of the two switches in a two stage rail.
Two devices in one 3 by 3 body is a packaging trick as much as a silicon one. The die are thinned and mounted side by side on a common lead frame with the pads split, so each device keeps its own drain and source. The thermal path is shared, which is why the junction to foot resistance is published as 25 K per watt typical against 29 maximum, and why the steady state ambient figure is worse than a single device in the same body.
The high side of a buck converter is the harder of the two positions. It carries the peak current for the on time, it has to be driven from a bootstrap above the rail, and its drain moves with the switching node, so the gate loop has to be short and the source inductance low. A device with 8 milliohm and 8.4 nC in that position is a reasonable match to a 1 MHz, 15 A per phase converter.
Key data for the VBQF3307
| Configuration | Dual N channel, independent |
| Package | DFN 3 by 3, split pads |
| VDS | 30 V per device |
| VGS | Plus or minus 20 V |
| Vth | 2.0 V |
| RDS(on) at 10 V | 8 milliohm |
| RDS(on) at 4.5 V | 13 milliohm |
| ID at a 25 C case | 30 A per device |
| Pulsed drain current | 90 A |
| Qg | 8.4 nC typical |
| Body diode | 1.2 V maximum at 9 A |
| RthJA | 39 K per watt typical, 53 maximum, steady state |
| RthJF | 25 K per watt typical, 29 maximum |
One field on the vendor page does not belong there. The threshold column prints 48 V, which cannot be a gate threshold on a 30 V part; the data sheet static table prints 2.0 V, and that is the number to use. The rest of the row set is consistent with the data sheet, so the page is usable, but a buyer reading the column at face value would reject the part or, worse, size a divider for a 48 V threshold.
The 13 milliohm at 4.5 V against 8 at 10 V is a 60 per cent step, larger than on a single device of the same voltage, because the two die share the same body and the same gate runner. On a bootstrap drive at 12 V the gate is 12 V above the source during the on time, so the 8 milliohm figure applies. On a 5 V rail the 13 milliohm figure is the one to use.
Two devices in a buck converter
The obvious use is a synchronous buck with both switches in one body: the high side carries the peak current for the on time and the low side carries the inductor current for the off time. With 8 milliohm on the high side and 13 on the low side at a 4.5 V drive, a 15 A converter at 1 MHz dissipates 0.3 W in the high side and 0.35 W in the low side, and the 39 K per watt ambient resistance holds both at a 50 K rise on a modest pad.
The second use is two independent high side switches in a multi rail system, which is what the notebook CPU core application implies. Each device has its own gate and its own source, and the pads are split, so the two rails do not share a node. That arrangement has to be checked in the land pattern: a pad that merges the two drains turns the pair into a single device with double the area and a short between two rails.
The third use is a load switch pair, one per rail, with a common gate signal. The bodies are independent, so a fault on one rail does not take the other down, which is the reason to pay for two die in one package rather than two separate parts.
Drive, dead time and the body diode
The body diode drop of 1.2 V at 9 A is high for a 30 V device, and it is the number that sets the loss during the dead time. In a 1 MHz converter with 20 ns of dead time at 15 A, each cycle carries 0.3 microcoulomb through the diode, which is 0.3 A of continuous current and 0.36 W. That is more than the switching loss, and it is why the dead time is trimmed to the shortest value that avoids shoot through.
The gate charge of 8.4 nC at 1 MHz is 8.4 mA per device, so a dual driver is needed for both switches. A single driver output feeding both gates through separate resistors is common, but the high side needs a bootstrap capacitor sized for the total charge of both devices if they are driven from the same node.
Where the pair has to be compared with two single devices on a board, the power management cross reference page covers which parameters have to match before the swap, and on a dual the sharing of the thermal path is the one that has no equivalent: two single parts give each die its own pad, and a dual concentrates both losses in one 3 by 3 footprint.
Buying this code
The vendor states 100 per cent gate resistance and unclamped inductive switching tests, halogen-free construction, and no automotive qualification. The dual body is a common source of confusion at incoming inspection, because a curve trace on pins 1 and 8 shows one device and the other device needs pins 3 and 6. An inspection plan that traces only one side will pass a part with a dead second die.
Where a line receives these in volume, the incoming inspection plan page covers what is checked on receipt, from the reel label to a sample curve trace on both devices, and it is the cheapest place to catch a mixed reel.
The two drains sit next to each other on one side of the body, and that is where the land pattern can go wrong. The body allows about 0.2 mm between the two drain pads, and a paste deposit that bridges the gap is invisible after reflow and shows up as a short between two rails at first power. An X-ray or a two point resistance check between the drain nets at first article is the reliable way to catch it, and the check takes a second per board.
The sourcing side of this part is covered on the power management cross reference. For a dual body compared against two single devices, that page covers which parameters have to match before the swap.
Questions we get on this code
Are the two devices isolated? Electrically yes, each has its own drain, source and gate. Thermally they share the lead frame, so the loss in one raises the other.
Can one device be left unused? Yes, with its gate tied to its source through a resistor. The unused die still adds capacitance to the shared pad, which costs a little switching loss on the used one.
Why is the threshold printed as 48 V on the vendor page? It is a data entry error. The data sheet prints 2.0 V, and a 48 V threshold on a 30 V device is not physically possible.
Is 30 A per device a working current? Only with the case at 25 C. In still air the pair is good for 12 to 15 A per device, and the steady state ambient resistance of 53 K per watt is the number that sets it.