Contact Us

VBQF1695

Brand: VBsemi
VBsemi VBQF1695 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1695 — Discrete & Power Semiconductors | Superb Automation

VBQF1695

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1695 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1695: a 60 V, 6 A N channel in a 1.07 mm body

The VBQF1695 is a single N channel MOSFET in the DFN 3 by 3 body at 60 V drain to source, 75 milliohm at a 10 V gate, 85 milliohm at 4.5 V, 6 A of drain current, 13 nC of total gate charge and 665 pF of input capacitance. The vendor highlights the package rather than the silicon: low thermal resistance, small size and a 1.07 mm profile. That is a part for a board with a height limit, and the electrical numbers are modest on purpose.

Sixty volts is the rating that covers a 48 V telecom rail with float at 57 V, a 48 V battery string at 54.6 V in charge, and a 36 V industrial supply with a 48 V transient. At 6 A the part is not a converter switch on a 48 V line; it is a switch, a clamp, a pre charge path or a class D output device. The 75 milliohm resistance at 6 A is 2.7 W, which the 3 by 3 pad carries with the junction to ambient resistance of 31 to 39 K per watt and no more than about 60 K of rise.

The applications named on the vendor page are a CCFL inverter and a class D amplifier, and both make sense for the same reason. A CCFL inverter runs a resonant tank at 50 to 100 kHz with a few hundred volts on the secondary, and the primary switch sees 12 to 24 V and a couple of amps. A class D output stage at 60 V runs a 4 ohm load with a switching frequency of 300 to 500 kHz, and a 6 A device covers a 100 W channel.

Key data for the VBQF1695

ConfigurationSingle N channel
PackageDFN 3 by 3, 1.07 mm profile
VDS60 V
VGSPlus or minus 20 V
Vth1.7 V typical
RDS(on) at 10 V75 milliohm
RDS(on) at 4.5 V85 milliohm
ID at a 25 C case6 A
ID at a 25 C ambient5.4 A
Pulsed drain current20 A
Qg13 nC typical
Ciss665 pF
RthJA31 K per watt typical, 39 maximum
RthJC5 K per watt typical, 6.3 maximum
Junction rangeMinus 55 to 150 C

The current figures step down sharply between the case and the ambient, 6 A to 5.4 A, because the case figure assumes the pad is held at 25 C and the ambient figure assumes a 1 inch square board. The pulsed rating of 20 A is the bond wire limit over a 10 microsecond width. Read together, the part is a 3 to 4 A continuous switch on a board with ordinary copper, and 5 A only with a plane under the pad.

The threshold of 1.7 V is low for a 60 V part and it is what allows the 4.5 V row to be only 13 per cent worse than the 10 V row. A low threshold in a 60 V device carries a leakage penalty at high temperature, and the data sheet's drain leakage row at 150 C is the number to check on a standby load, which the vendor prints in the microamp range for a die this size.

Class D output and resonant inverters

In a class D output stage at 48 V and 100 W into 4 ohm, the peak current is 7 A and the RMS per device is 2.6 A in a half bridge with a 50 per cent modulation. At 75 milliohm that is 0.5 W per device, and the switching loss at 400 kHz with 13 nC of gate charge and a 48 V rail is about 0.6 W. The two together are inside the thermal budget of the 3 by 3 pad, and this is exactly the application the vendor names.

In a CCFL inverter the part is the primary switch of a Royer or a current fed push pull at 12 V. The current is 2 to 3 A, the drain ring goes to twice the supply plus the leakage spike, and 60 V holds that with a clamp. The 20 A pulsed rating is comfortable for the commutation and the avalanche rating has to be checked against the leakage energy of the transformer, which the page does not publish.

The 1.07 mm profile matters where the board sits behind a display or inside a module with a metal lid. A standard 3 by 3 DFN is 1.0 to 1.1 mm, so this is not a special low profile part, it is a standard body described honestly. What matters more at that height is that the pad is soldered with no voids, because a void under a 3 by 3 pad in a 1 mm package is 30 per cent of the thermal path.

Drive and protection at 60 V

13 nC at 500 kHz is 6.5 mA of drive current, and an integrated driver handles it. The Miller plateau is longer than on the 30 V parts because the gate to drain charge is a larger fraction of the total at this voltage, so the switching transition is 20 to 30 ns and the drain ringing has to be damped. A 10 ohm gate resistor and a small RC snubber across the drain to source keep the peak inside 60 V on a 48 V rail with 20 nH of loop inductance.

The gate to source limit is plus or minus 20 V, and on a 48 V rail a source referenced drive that fails can put the full rail across the gate. A 15 V zener across gate and source is standard practice on these circuits, and so is a 10 k resistor from gate to source to hold the part off when the driver is unpowered.

Where a part in this class has to be second sourced, the power management cross reference page covers what has to be compared before a substitute is proposed, which at 60 V is the threshold, the gate charge and the body diode recovery, not only the resistance. A substitute with 60 milliohm and a 3 V threshold will not switch the same way in a resonant tank.

Buying this code

The page carries the electrical rows, the thermal rows, a halogen-free statement to IEC 61249-2-21 and no automotive qualification. For a display inverter in a consumer product that is enough. For a module that has to survive a qualification cycle, the vendor has to supply the high temperature leakage and the avalanche energy, since neither is on the page.

Where the same 60 V part is used across several products at different currents, the BOM consolidation page covers how a family is merged onto one code without losing a qualification, which is usually worth more than the price difference between two adjacent members.

The sourcing side of this part is covered on the BOM consolidation. For a 60 V part used across several products at different currents, that page covers how the family is merged onto fewer codes.

Questions we get on this code

Is 6 A a continuous rating? At a 25 C case with the pad held there, yes. On a board in still air the figure is 3 to 4 A, and the ambient rows on the data sheet, 5.4 A at 25 C and 4.3 A at 70 C, are the ones that apply.

Why does a 60 V part cost more than a 30 V part with lower resistance? The drift region has to be longer to hold 60 V, so the same die area gives four times the resistance. The price follows the die area needed to reach the resistance, not the voltage alone.

Can it drive a relay or a solenoid directly? Yes if the coil current stays under 3 A and a freewheel diode is across the coil. The avalanche energy of the coil is not published on this page, so the diode is not optional.

Is the 1.07 mm profile the lowest in the body? No, it is the standard height for a 3 by 3 DFN. What matters is the void-free solder joint under the pad rather than the millimetre of moulding above it.