Contact Us

VBQF1405

Brand: VBsemi
VBsemi VBQF1405 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1405 — Discrete & Power Semiconductors | Superb Automation

VBQF1405

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1405 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1405: a 40 V N channel with a 5 V capable gate

The VBQF1405 is the middle member of the 40 V family in the DFN 3 by 3 body: 4.5 milliohm at a 10 V gate, 6.2 milliohm at 4.5 V, 40 A of drain current, 9.8 nC of total gate charge and 1330 pF of input capacitance. The vendor lists it as capable of operation with a 5 V gate drive, which is the sentence that separates it from the 2 milliohm part in the same body, because a 3.8 V gate drive arrives at a resistance that is still inside the published curve rather than at the edge of it.

The 38 per cent gap between the 10 V and the 4.5 V resistance is larger than on the 2 milliohm part, and it is a threshold effect rather than a channel effect. At 4.5 V the channel is fully formed but the accumulation layer in the drift region is thinner, so the resistance is set by both. At 10 V the drift region is fully accumulated and only the channel remains. That is why a part sold for a 5 V drive has to be checked at 4.5 V and not at the headline gate voltage.

Forty volts and 4.5 milliohm is the combination used in a 12 V to 3.3 V or a 24 V to 5 V synchronous buck, in ORing on a redundant supply, and in a motor drive at a few amps. The body is small enough to sit next to the inductor, which is where the loop area is shortest and the ringing is lowest.

Key data for the VBQF1405

ConfigurationSingle N channel
PackageDFN 3 by 3, exposed pad
VDS40 V
VGSPlus or minus 20 V
Vth2.5 V typical
RDS(on) at 10 V4.5 milliohm
RDS(on) at 4.5 V6.2 milliohm
ID at a 25 C case40 A
Qg9.8 nC typical
Qgs3.2 nC
Ciss1330 pF
Body diode0.75 V typical, 1.2 V maximum
RthJA26 K per watt typical, 33 maximum at 10 s
Junction rangeMinus 55 to 150 C

The threshold of 2.5 V is the highest in this band, and it is what a 5 V gate drive has to clear. At 4.5 V the part is 2 V above threshold, which is enough for the published 6.2 milliohm, but at 3.3 V it is 0.8 V above threshold and the resistance is outside the published curve. A circuit that runs from a 3.3 V rail through a level shift to 4.5 V is at the edge of what the data sheet supports, and the loss should be measured rather than calculated.

9.8 nC at 1 MHz is 9.8 mA of drive current, half of what the 2 milliohm part needs for the same switching speed. That is the trade: 4.5 instead of 2 milliohm buys a driver that can be a small integrated one, and in a 10 A converter the extra conduction loss, 0.25 W at 10 A, is often less than the driver saving.

Synchronous buck, ORing and motor drive

In a 24 V to 5 V converter at 300 kHz and 10 A, the losses split roughly evenly: 0.62 W of conduction at 6.2 milliohm, 0.3 W of switching and 0.1 W of gate drive. At 10 A the part runs at a 30 to 40 K rise on a four square centimetre pad, which leaves the margin for a 60 C ambient. Above 15 A the same body is better replaced by the 2 milliohm part, and the crossover in a two part comparison is where the conduction loss starts to dominate the driver and Qoss savings.

In ORing, two of these sit with their body diodes facing the load so that either supply can feed the rail. The diode conducts until the gate is driven, and the gate has to be driven above the rail, which means a charge pump. The 20 V gate limit is comfortable there because the pump is referenced to the source and the difference, not the absolute voltage, is what counts.

In a brushed motor drive at 5 to 10 A the same part works as a low side switch with a PWM on the gate. The body diode carries the freewheel current during the off time, so the 0.75 V drop is in the path for most of the period at low duty. That is why a motor drive with a PWM below 30 per cent wants a parallel schottky rather than a bigger MOSFET.

Drive and the 5 V claim

The vendor's five volt claim rests on the 4.5 V row of the resistance table. At a 5 V drive the part is 2.5 V above threshold, and the curve in the data sheet is close to flat between 4.5 and 10 V at that point. The claim is not a guarantee at 3.3 V, and a circuit that pulls the gate to 3.3 V should treat the resistance as unpublished and the loss as unknown.

The gate charge of 9.8 nC with 3.2 nC of gate to source charge means the Miller plateau is short, so a 0.5 A driver switches the part in 20 ns. That is fast enough to ring the drain on a long trace, and a 4.7 ohm gate resistor plus a snubber across the low side is the usual cure. The switching loss at 300 kHz with a 24 V input is about 0.3 W at 10 A, which the thermal path handles without a heatsink.

Where the board is being re-quoted against a second source, the how to verify a drop in replacement page covers the bench checks that decide whether a substitute behaves the same, including the threshold, the gate charge and the body diode drop, all three of which differ across vendors at this resistance class.

Where a cost target has to be met across a family of converters, the how to reduce component cost page covers where the resistance can be traded against copper, frequency and driver cost rather than against the part price alone.

Buying this code

The page carries the resistance at two gate voltages, the charge, the capacitance and the thermal rows, and no avalanche energy figure. A part used in a motor drive with an inductive load needs that number, and the vendor has to supply it. The 100 per cent gate resistance and unclamped inductive switching tests are process statements, not a rating.

On a 3 by 3 body the reel label is the only readable record after reflow, and a mixed lot is common at distributor level. Where traceability matters, the supplier quality audit page covers what is checked at the source before a lot is released into a build.

Packing is a 3000 piece reel on 8 mm tape, and the tape decides whether the pick and place can run the code at all. A 3 by 3 body this thin needs a nozzle sized for the body, and a nozzle that is too large lifts the tape with the part and drops it twice in a thousand. Where the line already runs 0201 parts the same nozzle works, and on an older machine both the feeder and the nozzle change, which is a setup cost per build rather than per reel.

Questions we get on this code

Is 6.2 milliohm the number at a 5 V gate? It is the number at 4.5 V. At 5 V it is slightly lower, and the data sheet curve is the place to read it rather than an interpolation.

Can two of these be paralleled? Yes, with a separate gate resistor on each so the two share the current during the switching transition. Without it one part takes the whole turn on current and the pair is no better than a single part.

Is the body diode fast enough for a synchronous buck? The page gives the forward drop and no reverse recovery time. In a 300 kHz converter the dead time dominates, and a part with a slower diode only costs loss during that window.

What is the advantage over the 2 milliohm part in the same body? Half the gate charge and a driver that can be integrated. Below 10 A the two are close; above 15 A the resistance decides.