Contact Us

VBQF1303

Brand: VBsemi
VBsemi VBQF1303 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1303 — Discrete & Power Semiconductors | Superb Automation

VBQF1303

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1303 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1303: a 30 V N channel at 4 milliohm in a 3 by 3

The VBQF1303 is a single N channel MOSFET in the DFN8 3 by 3 body at 30 V, plus or minus 20 V on the gate, a 1.7 V threshold, 60 A of drain current, 5 milliohm at a 4.5 V gate and 4 milliohm at a 10 V gate. It is the middle member of the 30 V family in this body, between the 2 milliohm part and the 7.5 milliohm one.

Four milliohm at 10 A is 0.4 W and at 20 A is 1.6 W, so a 3 by 3 pad handles 15 to 20 A in still air. That is the sweet spot for this package: enough resistance to keep the die small and the gate charge moderate, low enough that a 12 V rail at 15 A does not need a heatsink.

The family exists because the same land pattern can then carry three current levels. A board rated for 15 A can drop in the 4 milliohm part and a board for 25 A the 2 milliohm part with no change to the copper, which is worth more in production than the few cents between them.

Key data for the VBQF1303

ConfigurationSingle N channel
PackageDFN8 3 by 3, exposed pad
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID60 A at a 25 C case
RDS(on) at 4.5 V5 milliohm
RDS(on) at 10 V4 milliohm
StructureTrench
Conduction at 10 A0.4 W
Conduction at 15 A0.9 W
Conduction at 20 A1.6 W
Conduction at 30 A3.6 W

Two of these in parallel give 2 milliohm on paper and 2.2 to 2.5 in practice, because the current does not divide exactly. The threshold spread inside one lot is small, but the resistance rises with temperature, so the part carrying more current gets hotter and takes a larger share until the two settle at a balance point. A separate gate resistor on each and a symmetric drain and source connection keep that point within 10 to 15 per cent, which is enough for a load switch and not enough for a precision current sense.

Where the 4 milliohm member fits

The first case is a 12 V to 5 V buck at 8 to 10 A, where the low side switch carries the inductor current for most of the period and 4 milliohm gives 0.4 W at 10 A. The high side in that converter can be a smaller part, so the pair costs less than two identical low resistance devices.

The second case is a two cell or three cell battery pack protection switch. At 15 A the drop is 60 mV and the loss is 0.9 W, which is inside what a 3 by 3 pad can dissipate with the pack's own copper around it. The 30 V rating covers a three cell pack at 12.6 V with margin for the charger.

The third case is an LED driver low side on a 12 or 24 V lamp, where the switch is pulse width modulated at 1 to 20 kHz and the resistance sets the efficiency. At 24 V and 2 A the loss is 16 mW, so the part is chosen for its package and its cost rather than for its resistance.

Choosing between 2, 4 and 7.5 milliohm

The three parts are the same die family at three sizes. Doubling the die halves the resistance and doubles the gate charge and the cost, so the choice is a comparison of conduction loss against drive loss and price at the actual current.

At 10 A the difference between 4 and 2 milliohm is 0.2 W, which does not justify the larger die. At 25 A it is 1.25 W, which is the difference between a 3 by 3 pad that works and one that does not. The crossover for this family sits around 15 A for most boards, and that is why the 4 milliohm part is the one that ships in volume.

Thermal behaviour and the pad

At 15 A the loss is 0.9 W and at 20 A it is 1.6 W from 4 milliohm. Hot, the resistance rises by about 40 per cent, so 20 A becomes 2.2 W and the 3 by 3 pad at 35 to 45 K per watt gives a 77 to 99 K rise. With the ambient at 60 C that is a 137 to 159 C junction, so 20 A needs either more copper or moving air.

The pad is the whole thermal path, and the vias under it matter as much as the copper around it. A 3 by 3 land pattern with six 0.3 mm vias into an inner plane is roughly 40 K per watt; the same pattern on a two layer board with no inner plane is 60 K per watt or worse, and that difference is what turns a 20 A build into a 12 A one.

Where the project needs a lower cost path at the same current, the how to reduce component cost page covers where the resistance can be traded against copper and where it cannot.

The 4.5 V column applies to a 5 V rail with a driver that pulls the gate to the rail, and to a 3.3 V system through a level shift that reaches 4.5 V. A 3.3 V rail without a level shift sits below the published point and gives a resistance between the 4.5 V figure and twice it, so the loss has to be measured rather than read. On a 12 V rail with a 10 V drive the 4 milliohm column applies, and the 5 milliohm figure is the conservative one to quote.

Efficiency across the load range is where the 4 milliohm member earns its place. At 20 A the loss is 1.6 W and the part is the largest single loss in a 5 V rail; at 2 A the same part loses 16 mW and the converter is dominated by its own quiescent current. That is why the family is carried in three resistances rather than one: a part sized for the peak current wastes board area and cost on a rail that idles, and a part sized for the idle current cannot carry the peak.

Thirty volts on a three cell pack is a margin of 2.4 against the 12.6 V full charge, which is comfortable for the pack and tight for the charger. A charger that loses regulation can push a 12.6 V pack towards 16 V, and a load that is switched off at the same instant produces an inductive kick on top of that. The 30 V rating covers both events on a protected line; on an unprotected one, a 40 V member of the same family is the safer choice for a few tenths of a milliohm.

The sourcing side of this part is covered on the pin to pin cross reference. For a mid resistance member of the same family, that page covers which parameters have to match before the member is changed.

Questions we get on this code

Is it a drop in for the 2 milliohm part? Same body and same land pattern, so yes mechanically. Electrically the resistance is double, so the loss and the temperature rise double with it.

Can it be driven from 4.5 V? Yes, the resistance is printed at that gate voltage, 5 milliohm. A 3.3 V drive is below the published point and needs characterising.

Is 60 A realistic on a board? No. It is a 25 C case figure. On a 3 by 3 pad, 15 to 20 A is where this part sits.

Does it need a gate resistor? Yes, unless the driver is in the same package. A 2 to 10 ohm resistor is the usual range for a 12 V rail at a few hundred kilohertz.