VBQF1302
Product Specifications
VBQF1302
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF1302 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF1302: a 30 V N channel at 2 milliohm in a 3 by 3
The VBQF1302 is a single N channel MOSFET in the DFN8 3 by 3 body at 30 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 70 A of drain current, 3 milliohm at a 4.5 V gate and 2 milliohm at a 10 V gate. Two milliohm in a 3 by 3 is close to the floor for trench silicon at this voltage, and it is reached by making the die as large as the package can carry.
The whole point of this part is conduction. At 2 milliohm and 20 A the loss is 0.8 W, which is less than a relay contact and less than a fuse, so it replaces a mechanical switch in circuits where a 20 to 40 A path has to be turned on and off under control. The trade is gate charge and cost per unit of resistance.
Its practical limit is not the die but the pad. The 70 A figure is a bond wire and die number at a 25 C case; the 3 by 3 pad on four square centimetres of copper carries about 25 to 30 A before the junction reaches 125 C in still air.
Key data for the VBQF1302
| Configuration | Single N channel |
| Package | DFN8 3 by 3, exposed pad |
| VDS | 30 V |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V typical |
| ID | 70 A at a 25 C case |
| RDS(on) at 4.5 V | 3 milliohm |
| RDS(on) at 10 V | 2 milliohm |
| Structure | Trench |
| Conduction at 10 A | 0.2 W |
| Conduction at 20 A | 0.8 W |
| Conduction at 30 A | 1.8 W |
| Conduction at 40 A | 3.2 W |
In a battery protection circuit the part sees two very different events. The first is the normal load, a few amps through 2 milliohm, which is a thermal question. The second is a short circuit, where the current is limited by the cell and the wiring to several hundred amps for the few microseconds before the protection IC turns the part off. That second event is a safe operating area question, and a 3 by 3 die with this much area can take it once; repeated shorts or a slow turn off are what destroy these parts in the field.
Where a 2 milliohm part is used
The first case is a battery protection switch on a single cell or a two cell pack. The part sits in the low side of the pack, carries the full load current, and has to be turned off cleanly when the protection IC detects an overcurrent. At 2 milliohm and 10 A the drop is 20 mV and the loss is 0.2 W, which is what makes a 3 by 3 body enough for a 10 A pack.
The second case is a high current load switch on a 12 V rail, where several outputs share one input. A 20 A output through 2 milliohm loses 0.8 W, and the same output through a 10 milliohm part loses 4 W, so the resistance is what buys the absence of a heatsink.
The third case is a synchronous buck low side at 300 to 500 kHz on a 12 V to 1.x V rail. The low side conducts for most of the period at a low duty, so its resistance sets the conduction loss while the high side sets the switching loss. Pairing a 2 milliohm low side with a smaller high side is the standard arrangement.
Gate charge, and the price of low resistance
A 2 milliohm die has a large gate area, so its gate charge is high, typically in the 40 to 80 nC range for this class. At 500 kHz and 10 V that is 0.2 to 0.4 A of average gate current, which the driver has to supply and which shows up as a loss of 2 to 4 W in the driver and the gate resistor if the drive is not stiff.
This is why the low resistance part belongs on the low side, where it switches once per cycle at a low voltage across it, and not on the high side of a converter where the switching loss is multiplied by the full rail. Used the other way round, the conduction gain is eaten by the switching loss and the part runs hotter than a smaller one.
Thermal behaviour and the pad
At 20 A the loss is 0.8 W, at 30 A it is 1.8 W and at 40 A it is 3.2 W from 2 milliohm. Hot, the resistance rises by about 40 per cent, so 30 A becomes 2.5 W. A 3 by 3 pad on four square centimetres of two ounce copper is around 35 to 45 K per watt in still air, so 30 A is a 88 to 113 K rise, which is workable with an ambient of 50 C and not workable at 85 C.
The pad is also the only heat path. A 3 by 3 body has no lead frame tab to speak of, so vias under the pad into an inner copper plane are what carry the heat away on a multilayer board. Six to nine vias of 0.3 mm inside the pad are the usual figure, and their thermal resistance is often larger than the copper spreading resistance around them.
When a BOM carries three or four 30 V parts at different resistances, the BOM consolidation page covers how the class is merged without losing the qualification that was already signed off on the individual codes.
Vias under the pad carry more heat than the copper around the pad on a 3 by 3 part. Six vias of 0.3 mm plated to 25 microns are about 100 K per watt each, which is 17 K per watt for the group, better than the spreading resistance of the copper itself. The catch is solder wicking: an untented via inside the pad pulls paste away from the joint during reflow and leaves a void exactly where the heat has to leave. Tented or plugged vias are the usual answer, and the assembly note has to say which one is used.
Compared with a relay, a 2 milliohm part has no contact wear, no coil current and a drop of 20 mV at 10 A instead of a contact resistance that rises with age. What it does not have is isolation: the body diode and the channel both connect drain to source, so a failed part fails short, and a circuit that needs a physical break still needs a relay or a fuse in series. The usual arrangement is the part as the controlled switch and a fuse as the last resort, with the fuse rated above the load and below what the cell can deliver into a short.
The sourcing side of this part is covered on the how to reduce component cost. For a 2 milliohm part carried across several builds, that page covers where the resistance can be traded against copper and price.
Questions we get on this code
Can it carry 70 A? Not on a board. That is the die and bond wire figure at a 25 C case. On a 3 by 3 pad in still air, 25 to 30 A is the honest continuous point.
Is 2 milliohm measured at 25 C? Yes, and it rises with temperature. At 125 C the same part is nearer 2.8 milliohm, which changes the loss by 40 per cent.
Why is the 4.5 V figure 50 per cent higher? Because the channel is not fully enhanced at 4.5 V. A 3.3 V logic drive will be worse again, and the part should not be used that way at high current.
Does it have a built in gate resistor? No. The gate resistor is external and is what sets the switching speed and the ringing on the switch node.