Contact Us

VBQF1104N

Brand: VBsemi
VBsemi VBQF1104N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1104N — Discrete & Power Semiconductors | Superb Automation

VBQF1104N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1104N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1104N: 100 V and 36 milliohm in DFN 3 by 3 for a primary side switch

The VBQF1104N is a 100 V N channel MOSFET in the DFN 3 by 3 body with an exposed pad, and the sheet names one application, primary side switch. The summary prints 100 V, 0.036 ohm at a 10 V gate, 0.0375 ohm at 8 V, 21 A continuous at a 25 C case and 23 nC of gate charge, and the feature list leads with an extremely low gate drain charge and a 100 per cent avalanche test.

The low gate drain charge is real and it is the reason to look at the part. Gate drain charge is 6.5 nC against a total gate charge of 28.5 nC at 10 V, so the Miller plateau is 23 per cent of the total rather than the 40 to 60 per cent common in this voltage class. A low plateau means the drain moves quickly once the gate reaches threshold, which is what a flyback primary wants.

The current table has four rows, 21 A at a 25 C case, 17 A at 70 C, 15 A on a board in 25 C air and 13 A in 70 C air. The dissipation rows are 5.9 W at a 25 C case and 3.1 W on a board, and those two are small for a 21 A rating, which is the first sign that the current figure is not a thermal one.

The threshold window is high for a trench part: 2.5 V minimum and 4.5 V maximum. A 4.5 V gate drive is at the bottom of that window and the sheet accordingly specifies on resistance at 10 V and at 8 V but not at 4.5 V. A converter that drives this part from a 5 V logic rail is outside the published operating points.

The parameter table in full

Drain to source voltage100 V
Gate to source voltage, continuousplus or minus 20 V
Continuous drain current, case at 25 C21 A
Continuous drain current, case at 70 C17 A
Continuous drain current, board at 25 C and 70 C15 A and 13 A
Pulsed drain current50 A
Continuous diode current, case at 25 C4.5 A in the ratings table, 7.7 A in the diode table
Single pulse avalanche current, 0.1 mH20 A
Single pulse avalanche energy20 mJ
Maximum power dissipation, case at 25 C and 70 C5.9 and 3.8 W
Maximum power dissipation, board at 25 C and 70 C3.1 and 2 W
Junction to ambient, 10 s, typical and maximum33 and 40 C per watt
Junction to ambient, steady state maximum80 C per watt
Junction to foot, typical and maximum17 and 21 C per watt
Breakdown voltage temperature coefficient172 mV per C
Gate threshold temperature coefficientminus 10 mV per C
Gate threshold at 250 microamp2.5 V minimum, 4.5 V maximum
Gate leakage at 20 V100 nA maximum
Drain leakage at 100 V, 25 C and 55 C1 and 10 microamp
On state drain current at 10 V gate30 A minimum
On resistance at 10 V gate and 5 A0.036 ohm typical
On resistance at 8 V gate and 5 A0.0375 ohm typical
Forward transconductance at 5 A23 S typical
Input, output and reverse transfer capacitance at 50 V1735, 160 and 37 pF
Total gate charge at 10 V and at 8 V28.5 and 23 nC typical
Gate source and gate drain charge8 and 6.5 nC
Gate resistance at 1 MHz0.85 and 1.3 ohm
Turn on delay and rise time at 10 V drive14 and 12 ns typical
Turn off delay and fall time at 10 V drive22 and 6 ns typical
Turn on delay and rise time at 8 V drive16 and 12 ns typical
Body diode forward drop at 2.6 A0.77 V typical, 1.2 V maximum
Body diode recovery time63 ns typical, 95 maximum
Body diode recovery charge110 nC typical, 165 maximum
Reverse recovery fall and rise time49 and 14 ns
Operating junction and storage rangeminus 55 to plus 150 C

Five point nine watts against a twenty one amp rating

Twenty one amps at 36 milliohm is 15.9 W, which is nearly three times the 5.9 W the case level row allows. The two figures cannot hold together at a 25 C case, since 15.9 W through 21 C per watt is 334 C of rise. The current row must be a bond wire and lead frame limit at a low duty cycle, and the dissipation row is the part of the table that describes continuous operation.

Working from the thermal row, the continuous current is much lower. 5.9 W through 36 milliohm is 12.8 A at the cold resistance, and through a doubled hot figure of 0.072 ohm it is 9 A. On a board the 40 C per watt row allows 3.1 W, which is 9.3 A cold and 6.6 A hot. A flyback primary carrying 8 A average in a 60 C cabinet is at the edge of the board allowance rather than in the middle of it.

The junction to foot path is the one that matters in a small body. 17 C per watt typical and 21 maximum means the heat leaves through the exposed pad, so the pad area, the number of thermal vias and the copper on the other side set the real figure. A 3 by 3 part with a 25 square millimetre pad is a different component from the same part with a 100 square millimetre pad.

Where the rows read past each other

The avalanche row and its test agree exactly. Twenty millijoules is printed against a 0.1 mH coil at 20 A, and half of 0.1 mH times 400 is 20 mJ. That makes the row usable for a flyback leakage clamp without a separate report, and it is one of the few rows in this shipment where the printed energy matches the stated test.

The diode current appears twice, 4.5 A in the ratings table and 7.7 A in the diode table, and the pulse row is 50 A in both. A 100 V part with a 21 A channel and a 4.5 A diode is a plausible narrow diode, so the ratings table is the one we use, and the 7.7 A row looks copied from the diode pulse condition.

The drain leakage test is at 55 C rather than the 125 C used elsewhere in this band, and the temperature coefficient of breakdown voltage, 172 mV per C, is higher than the 81 mV per C printed on the 100 V single channel part in the same family. At 150 C the breakdown rises by 21.5 V, which is a useful margin on a 100 V rail with a 60 V reflected voltage, and it is worth knowing when a converter runs hot.

Where a 100 V, 36 milliohm, low plateau part earns its place

A 30 W to 60 W flyback primary from a 48 V or a 400 V rail with a 100 V clamp, a boost converter at 20 kHz, an active clamp auxiliary and a hot swap switch on a 48 V line all fit inside the board allowance up to about 8 A. The low gate drain charge makes the drain edge 6 ns, which keeps the crossover loss under 1 W at 8 A and 100 V.

It does not fit above 10 A continuous in a small body, and it does not fit a 5 V gate drive, since the threshold maximum of 4.5 V leaves no overdrive. A larger body or a lower threshold part is the answer in both cases, and the 172 mV per C breakdown coefficient means there is room to trade voltage for resistance.

Our power management cross reference work keeps the gate drain charge, the threshold window and the junction to foot resistance per approved alternate, because a low plateau part and a high plateau part with the same on resistance produce different switching losses at the same drive, and only the gate drain row shows it.

Questions we answer before a reel is booked

First, the drive. With a 2.5 V floor and a 4.5 V ceiling the part needs a 10 V gate drive to be safely on, and the sheet's on resistance rows stop at 8 V. A converter with a 5 V logic rail needs a level shifter or a different part, and the 10 mV per C threshold coefficient means a hot die turns on more easily but also leaks more.

Second, the pad. The junction to foot row of 21 C per watt maximum assumes a soldered exposed pad, and a 3 by 3 part with voids is a different thermal component. We ask for the via pattern and the void limit before approving a 8 A continuous position.

Third, the alternate. A 100 V part at 30 to 40 milliohm in a 3 by 3 body comes with gate drain charges from 5 to 15 nC and threshold windows from 1.5 to 4.5 V, and the pair decides both the drive and the switching loss. We hold those rows per approved alternate, the incoming inspection plan checks the lot against them, and the pin to pin comparison starts from the 3 by 3 land pattern and the pad dimension rather than from the current rating.