Contact Us

VBQA3638

Brand: VBsemi
VBsemi VBQA3638 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA3638 — Discrete & Power Semiconductors | Superb Automation

VBQA3638

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA3638 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA3638: two 60 V N channels in a DFN 5 by 6

The VBQA3638 is a dual N channel MOSFET in the DFN8 5 by 6 B body at 60 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 17 A per channel, 38 milliohm at a 4.5 V gate and 32 milliohm at a 10 V gate. It is the 60 V member of the dual family, so the two channels are a pair of low side switches on a 48 V rail or a pair of 36 V load paths.

Sixty volts on a 48 V rail leaves a margin of 1.25 against float, which is thin for a line with an inductive transient and normal for a protected one. That is the same decision as on the single channel parts: the clamp decides the rating, and a 60 V part with a 57 V TVS is a workable pair while a 60 V part on an unprotected 48 V line is not.

The resistance is 32 milliohm per channel, so the two channels in parallel would be 16 milliohm before any derating, and each channel on its own carries 5 to 8 A comfortably on a board. The 17 A figure is per channel at a 25 C case, and it falls once both channels are loaded.

Key data for the VBQA3638

ConfigurationDual N channel, two separate channels
PackageDFN8 5 by 6 B, exposed pad
VDS60 V per channel
VGSPlus or minus 20 V
Vth1.7 V typical
ID17 A per channel at a 25 C case
RDS(on) at 4.5 V38 milliohm per channel
RDS(on) at 10 V32 milliohm per channel
StructureTrench
Conduction at 3 A0.29 W per channel
Conduction at 5 A0.8 W per channel
Conduction at 8 A2.05 W per channel
Both channels at 8 A4.1 W in one package

Two channels mean two gate drives, and on a dual body they are separate pins. A single driver with two outputs is the compact answer, but that driver has to sink the combined gate charge at the switching frequency, and its ground has to return to the source pins rather than to the board plane, or the source inductance of one channel appears in the gate loop of the other. Where both channels switch at the same instant, a common source connection is the worst case for that coupling.

Where a dual 60 V part fits

The first case is a two channel 48 V load switch, one rail per channel, with each channel's gate driven from its own open drain signal. At 5 A per channel the loss is 0.8 W per channel and 1.6 W in the package, which a 5 by 6 pad carries with a 40 to 50 K rise.

The second case is a half bridge built from two of these, or from one of these plus two gate drives, for a low frequency bridge such as a solenoid or a Peltier driver. The channels are separate, so one is the high side and one the low side, and the high side needs a floating drive because the source moves with the bridge node.

The third case is a two output converter where the two switches run at the same frequency and the same duty. Sharing a pad keeps the two hot dies at the same temperature, which is what a current sharing scheme needs to stay balanced.

The 60 V drift region in a 5 by 6

At 60 V the drift region is a real part of the resistance. The 32 milliohm figure is about 1.8 times the 30 V part in the same body, and that ratio comes from the drift region rather than the channel. It also means the part has more capacitance per unit of resistance than a 30 V part, so the gate charge is higher and the switching loss is higher at the same frequency.

For a load switch running in the hertz range, none of that matters. For a converter running at 300 kHz, the crossover frequency and the drive strength have to be chosen against the gate charge, and a 60 V part at the same resistance as a 30 V part will switch slower. That is why the 60 V parts belong in protection and disconnect circuits and in converters below 100 kHz.

Losses and the pad

At 5 A the loss is 0.8 W per channel from 32 milliohm, at 8 A it is 2.05 W, and with both channels at 8 A the package sees 4.1 W. Hot, the resistance rises by about 40 per cent, so the pair is nearer 5.7 W and the pad on four square centimetres of copper gives a 140 to 170 K rise at 25 to 30 K per watt.

The usable continuous point is 5 A per channel with both loaded, or 8 A with one channel loaded and the other idle. The 17 A per channel headline is the die and bond wire limit at a 25 C case, which is a package capability, not something a board will reach without a metal core.

When the sourcing question is which of two equivalent dual bodies to release, the supplier scorecard page covers how the source is scored on lot quality and delivery rather than on the data page alone.

The B suffix on the 5 by 6 body marks a pinout variant, and it is not interchangeable with the plain body on a board. The land pattern is the same size and the pad sits in the same place, so the two look alike in a drawing, and the difference is which pin carries which node. A substitution between the two is a board change rather than a part change, and the drawing has to be checked pin by pin before a second source is proposed on the strength of the package name alone.

On a 48 V line the two channels usually serve a main path and an auxiliary path, or two outputs of one rectifier. The question is not the resistance but the inrush into the bulk capacitance of each output: at 48 V and 220 microfarad the charge is 10.6 millicoulombs, and a turn on spread over half a millisecond gives about 21 A of average current through a channel rated at 17 A. The gate resistor sets that ramp. Without it the part takes the whole capacitor charge in a few microseconds and the safe operating area, not the resistance, decides whether it survives.

Sixty volts is not generous on a 48 V line once the clamp is chosen. A transient suppressor with a 58 V standoff clamps at about 93 V at its rated peak pulse current, which is well above this part, so a 60 V device only works behind a lower clamp, a slower transient or a series inductance that limits the pulse. Where the line can see a full telecom surge, the part has to be a 100 V device or the clamp has to be a 48 V standoff type with the energy it can absorb checked against the waveform.

The sourcing side of this part is covered on the BOM scrubbing. For a dual body being introduced into an existing BOM, that page covers how the line is checked against the qualification already in place.

Questions we get on this code

Is the pad common to both channels? The vendor electrical table does not say. Read the package drawing before the land pattern is made, because a common pad ties the two drains together.

Can the channels be used as a half bridge directly? Yes if the pad is not common to both drains. With a common pad the two drains are one node and the part becomes a low side pair only.

Why is the threshold 1.7 V on a 60 V part? It is a trench process choice that keeps the part usable on a 5 V drive. The trade is a higher off state leakage at 125 C than a part with a 3 V threshold.

Does 17 A per channel apply with both on? No. The package dissipates both losses through one pad, so the pair is well below 34 A in total.