VBQA3151M
Product Specifications
VBQA3151M
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQA3151M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQA3151M: a dual 150 V N channel pair at 0.090 ohm in DFN 5 by 6
The VBQA3151M is a dual N channel 150 V MOSFET in the DFN 5 by 6 body, two independent channels in one package with separate gate, drain and source pins. The summary prints 150 V, 0.090 ohm at a 10 V gate, 0.100 ohm at 4.5 V, 8 A continuous at a 25 C case and a 175 C junction limit, and the sheet describes the technology as a trench power MOSFET with material categorization stated rather than a specific die generation.
Two channels in one body is the reason to look at this part. A half bridge, a push pull primary, a dual output converter or a polarity switch can be built from one package with matched channels, which saves board area and keeps the two devices at the same temperature. The price is thermal coupling: two channels sharing one lead frame share one thermal path, and the 8 A per channel rating assumes only one of them is dissipating at a time.
The rating table has three current rows, 8 A at a 25 C case, 6.4 A at 100 C, and a pulsed row of 24 A. The diode current row prints 76 A and the avalanche current prints 82 A, both larger than the channel rating, which is the first sign that this sheet has rows copied from a different device and needs to be read row by row rather than as a whole.
The channel resistance is printed at three temperatures, 0.090 ohm at 25 C, 0.135 at 125 C and 0.225 at 175 C, so the loss at a given current more than doubles across the range. At 8 A the 25 C loss is 5.76 W per channel and the 175 C loss is 14.4 W, which is the number that decides whether a two channel package is viable at all.
The parameter table in full
| Drain to source voltage | 150 V |
| Gate to source voltage, continuous | plus or minus 20 V |
| Continuous drain current, case at 25 C | 8 A per channel |
| Continuous drain current, case at 100 C | 6.4 A per channel |
| Pulsed drain current | 24 A |
| Continuous source current, diode conduction | 76 A as printed |
| Avalanche current | 82 A as printed |
| Single avalanche energy at 0.1 mH and 1 per cent duty | 110 mJ |
| Maximum power dissipation, case at 25 C | 136 W as printed |
| Maximum power dissipation, board at 25 C | 3 W for 10 s, 8.3 W |
| Junction to ambient, 10 s, typical and maximum | 15 and 18 C per watt |
| Junction to ambient, steady state, typical and maximum | 60 and 50 C per watt as printed |
| Junction to case, typical and maximum | 0.85 and 1.1 C per watt |
| Breakdown voltage at 250 microamp | 150 V |
| Gate threshold at 250 microamp | 1 V minimum, 2 V typical, 3 V maximum |
| Gate body leakage at 20 V | 100 nA maximum |
| Drain leakage at 75 V, 25 C, 125 C and 175 C | 1, 50 and 250 microamp |
| On state drain current at 10 V gate | 60 A minimum |
| On resistance at 10 V gate and 20 A, 25 C | 0.090 ohm typical |
| On resistance at 10 V gate and 20 A, 125 C | 0.135 ohm typical |
| On resistance at 10 V gate and 20 A, 175 C | 0.225 ohm typical |
| On resistance at 4.5 V gate and 12 A | 0.100 ohm typical |
| Forward transconductance at 20 A | 60 S typical |
| Input, output and reverse transfer capacitance at 100 V | 600, 470 and 225 pF |
| Total gate charge at 10 V, 100 V and 50 A | 89 nC typical, 70 nC maximum as printed |
| Gate source and gate drain charge | 26 and 23 nC |
| Turn on delay and rise time at 50 A and 2.5 ohm | 21 and 15 ns typical |
| Turn off delay and fall time, same conditions | 35 and 20 ns typical |
| Pulsed diode forward current | 24 A |
| Body diode forward drop at 20 A | 1.0 V typical, 1.5 V maximum |
| Body diode recovery time | 4 ns typical, 135 ns maximum as printed |
| Operating junction and storage range | minus 55 to plus 175 C |
Two channels, one lead frame, and eight amps per channel
The 8 A rating with the case at 25 C is small for a 5 by 6 package, and it is small because 150 V silicon has a larger die area for the same resistance than a 60 V part does. 0.090 ohm at 8 A is 5.76 W, and 5.76 W through the 1.1 C per watt case path is 6.3 C of rise, so the case temperature is doing all the work and the current rating is not a thermal limit at 25 C.
At 100 C the rating falls to 6.4 A, which at 0.135 ohm is 5.5 W, and the two rows are close enough to be the same thermal budget seen through two ambient figures. The interesting number is the board row: 8.3 W for 10 s and 3 W at 25 C ambient, which for two channels sharing the package means 1.5 W per channel, and 1.5 W through 0.090 ohm is 4 A per channel. A dual package on a board therefore delivers half of what the case level table promises.
The junction to ambient pair is printed as 60 C per watt typical and 50 C per watt maximum, which is the wrong way round, since a typical figure cannot be worse than the maximum for the same part. Read the 50 C per watt as the maximum and the steady state allowance is 2.5 W for the whole package, not per channel.
The rows in this sheet that belong to another device
Three rows are inconsistent with an 8 A dual part. The diode current of 76 A and the avalanche current of 82 A are both an order of magnitude above the channel rating, and the avalanche energy of 110 mJ against a 0.1 mH coil at 82 A would store 336 mJ, so the test described cannot produce the energy printed. These three rows match the single channel 60 V part in the same family, and they were carried over when the sheet was assembled.
The gate charge columns are reversed. 89 nC is printed under typical and 70 nC under maximum, which would make the maximum smaller than the typical, and the gate charge of a 150 V dual channel die at 100 V and 50 A is more likely near 89 nC typical with a maximum nearer 130 nC. The gate source charge of 26 nC and gate drain charge of 23 nC are consistent with the 89 nC figure rather than the 70.
The capacitance rows are also hard to reconcile. An input capacitance of 600 pF with an output capacitance of 470 pF and a reverse transfer of 225 pF leaves only 375 pF of gate source capacitance, and a reverse transfer of 225 pF against 600 pF of input is a ratio of 0.375, which is far above the 0.01 to 0.05 that a trench power MOSFET normally shows. Two of these three numbers are probably from a smaller die.
The recovery time is the last one. Four nanoseconds typical against 135 ns maximum is a ratio of 34 to 1, and 4 ns is not a body diode recovery figure for a 150 V MOSFET. Use the 135 ns maximum when a synchronous stage is being assessed, and do not size a dead time on the typical.
Where a dual 150 V part earns its place
A 48 V to 150 V boost, a push pull primary from a 24 V rail, a polarity reversal switch and a two channel load switch all fit inside the ratings when each channel carries 4 A or less on a board. The matched channels and the shared temperature are worth more than the current figure in those positions, because a half bridge with two discrete parts at different temperatures drifts apart.
It does not fit a continuous 8 A per channel load on a board, a 150 V rail with a high leakage spike, or a synchronous rectifier that expects the body diode to carry current for a long dead time. A single channel part or a larger body is the answer in all three cases.
Our power management cross reference work records which rows of a dual sheet were inherited from a single channel sibling, because a dual part with 76 A of diode current printed on it will be selected for the wrong job if only the summary page is read, and the channel rating is the number that actually limits the circuit.
Questions we answer before a reel is booked
First, the channel count and the sharing. Two channels in one package share a thermal path, so a half bridge that switches one channel at a time is fine while a dual load switch that runs both at 4 A is not. We ask for the duty cycle per channel before approving the position.
Second, the drive. With a 1 V to 3 V threshold and a 600 pF input capacitance the part turns on easily, but the 225 pF reverse transfer figure, if it is real, would give a Miller plateau long enough to matter at 150 V. We check the plateau on the bench rather than trusting the row.
Third, the alternate. A 150 V dual part at 0.09 to 0.15 ohm comes in the same 5 by 6 body from several suppliers with channel counts, diode ratings and thermal rows that differ by a factor of five. We hold the real channel rating per approved alternate, the incoming inspection plan checks the lot against it, and the pin to pin comparison starts from the dual land pattern and the pinout order, since a dual part with the two drains on opposite sides will not drop into the same footprint.