Contact Us

VBQA2658

Brand: VBsemi
VBsemi VBQA2658 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA2658 — Discrete & Power Semiconductors | Superb Automation

VBQA2658

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA2658 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA2658: a minus 60 V P channel with a 50 milliohm channel

The VBQA2658 is a single P channel MOSFET in the DFN8 5 by 6 body at minus 60 V drain to source, plus or minus 20 V on the gate, a minus 1.6 V threshold, minus 30 A of drain current, 60 milliohm at a 4.5 V gate and 50 milliohm at a 10 V gate. It is the top of the P channel voltage range in this band and the part that shows how the drift region takes over the resistance.

At 60 V the on resistance is 50 milliohm, five times the 40 V part in the same body. The channel resistance has not changed; the extra is drift region, which grows with the square of the breakdown voltage and cannot be avoided in a trench structure. A superjunction P channel would do better, and it does not exist at this price point.

Sixty volts is the rating that covers a 48 V telecom rail with float at 57 V, a 48 V battery string at 54.6 V in charge, and a 36 V industrial supply with a 48 V transient. Those are the three lines where this part appears, and in all three the alternative is an N channel with a charge pump or an isolated drive.

Key data for the VBQA2658

ConfigurationSingle P channel
PackageDFN8 5 by 6, exposed pad
VDSMinus 60 V
VGSPlus or minus 20 V
VthMinus 1.6 V typical
IDMinus 30 A, a die figure at a 25 C case
RDS(on) at 4.5 V60 milliohm
RDS(on) at 10 V50 milliohm
StructureTrench
Conduction at 3 A0.45 W
Conduction at 5 A1.25 W
Conduction at 10 A5 W
Conduction at 20 A20 W

On a 48 V standby rail the off state leakage is the number that matters. A 60 V trench die at 125 C leaks in the tens of microamps with the gate at the source, and that current flows through whatever sits downstream. Over a year it is a quarter of an amp hour, which is nothing for a line card and a real drain for a battery string that has to sit for a season. The figure to check is the leakage at the top of the temperature range, printed in the full datasheet, rather than the 25 C number usually quoted in a comparison table.

Where a 60 V P channel earns its place

The first case is the input disconnect on a 48 V line card. The rail is 48 to 57 V, the switch has to hold the full rail when off, and the current is 2 to 5 A. At 5 A and 50 milliohm the loss is 1.25 W, which a 5 by 6 pad handles, and the gate is pulled down by an open drain signal referenced to the rail through a resistor and a zener.

The second case is reverse battery protection on a 48 V string, where the part conducts through its body diode in normal operation and is turned on to bypass the diode. In the on state the drop falls from 0.7 V to 0.25 V at 5 A, which is worth 2.25 W on a 48 V system that runs continuously.

The third case is a pre charge path. The resistor limits the inrush into the bulk capacitance and the P channel shorts the resistor once the rail is up. In that use the current is low and the part is chosen for its voltage rating and its package rather than for its resistance.

The threshold of minus 1.6 V, and leakage

A minus 1.6 V threshold is low for a 60 V part. It means the part is partly on at a gate 2 V below the source, which helps when the drive is a 5 V rail rather than a 10 V one, and it also means the off state leakage at 125 C is higher than on a part with a minus 2.5 V threshold. On a 48 V standby rail that has to hold for years, the leakage has to be added up across the whole board rather than taken part by part.

The other consequence is a soft turn on. Between the threshold and full enhancement there is 5 to 6 V of gate swing, and while the gate crosses that region the part is a resistor in the hundreds of milliohms and the load capacitance is charging through it. A gate resistor and a defined ramp on the drive keep that in the safe area; a fast drive straight onto the gate can put the part through the linear region in a microsecond.

Losses, and the comparison with an N channel

At 5 A the loss is 1.25 W, at 10 A it is 5 W and at 20 A it is 20 W. Hot, the resistance rises by about 40 per cent, so 10 A is really 7 W. The pad on four square centimetres of copper is 25 to 30 K per watt, which puts 10 A at 175 to 210 K of rise, so the honest continuous current is 5 to 6 A and the part is a 3 to 5 A device on a practical board.

That is the number to compare against an N channel solution. A 60 V N channel at 10 milliohm in the same body would give 0.25 W at 5 A, but it needs a charge pump, a bootstrap capacitor and a drive that survives the 48 V common mode. For 2 to 5 A and a switching rate in the hertz range, the P channel with 1.25 W is usually the smaller, cheaper circuit.

When the sourcing question is whether to keep this part or consolidate the family, the power management cross reference page covers how the adjacent voltage classes are compared on the parameters that matter in a fixed board, which are threshold, gate charge and body diode direction.

The body diode of a P channel points from drain to source, so in a reverse protection circuit it conducts whenever the input is correct and the switch is off. At 5 A that is 3.5 W in the diode, which is why the part is turned on rather than left to conduct. Once it is on, the drop falls to 0.25 V and the loss to 1.25 W. The gate drive therefore has to be present before the load current arrives, and a circuit that relies on the diode alone runs the die at its own loss with no way to turn it off.

On a 48 V line the part is driven from the rail through a level shift and a series resistor, and during turn on the gate crosses the 2 to 6 V window in a time set by that resistor and the gate capacitance. Inside that window the part is a resistance of a few ohms charging the load capacitance, so the current is set by the load rather than by the part. At 48 V and 100 microfarad the charge is 4.8 millicoulombs, and a turn on spread over 200 microseconds gives an average current of 24 A. That is what the gate resistor is for: it keeps the current inside the rating while the capacitor charges, and it is also why a P channel disconnect is not a hot swap controller. A hot swap path needs current limiting and a timer, not a larger gate resistor.

The sourcing side of this part is covered on the BOM consolidation. For a 60 V P channel code held on one line, that page covers how the class is merged without losing a qualification.

Questions we get on this code

Can it switch a 48 V rail at 100 kHz? No. The turn off is set by the gate to source resistor and lands in the tens of microseconds. This is a disconnect and protection part.

Is 30 A a continuous rating? It is a die figure at a 25 C case. On a board the pad limits the part to 5 or 6 A before the junction reaches 125 C.

What protects the gate on a 48 V line? A zener from gate to source plus a series resistor, and a resistor from gate to source that keeps the part off if the drive signal is missing.

Does the low threshold cause a problem at high temperature? It raises the leakage. Check the leakage at 125 C against the standby budget of the rail rather than at 25 C.