Contact Us

VBPB19R20S

Brand: VBsemi
VBsemi VBPB19R20S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBPB19R20S — Discrete & Power Semiconductors | Superb Automation

VBPB19R20S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBPB19R20S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBPB19R20S: 900 V and 20 A in TO3P at 270 milliohm

The VBPB19R20S is a single N channel MOSFET in the TO3P body, printed at 900 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of drain current and 270 milliohm at a 10 V gate. The structure is SJ_Multi-EPI, the multi epitaxial superjunction die, the same family as the higher current member of this band but on a smaller die and in a smaller package.

This is the auxiliary supply part for a high voltage bus. A 480 V drive or a 700 V solar string has control boards, gate drivers, fans and contactors that all need 12 or 24 V, and that supply is 20 to 100 W. It sits on the same 680 V bus as the main switches, so it needs the same voltage class, and it draws 100 to 500 mA, so it needs a small die with low capacitance rather than a large one with low resistance.

270 milliohm is a high number by the standards of the low voltage band and it is the correct number here. At 500 mA the die makes 68 mW. At 2 A it makes 1.1 W. A 20 A part at 270 milliohm is oversized on current and correctly sized on voltage, and it costs less than the 47 A member of the same family because the die is smaller.

Key data for the VBPB19R20S

ConfigurationSingle N channel
PackageTO3P, through hole, tab on the drain
VDS900 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID20 A at a 25 C case
RDS(on) at 10 V270 milliohm
StructureMulti epitaxial superjunction
Conduction at 1 A0.27 W
Conduction at 3 A2.4 W
Conduction at 8 A17.3 W
Conduction at 20 A108 W

Auxiliary supplies on a 680 V bus

The usual circuit is a flyback. The switch sits on the high side of the primary, the transformer primary sees the bus during the on time, and the reflected output voltage plus the leakage spike sits across the switch during the off time. On a 24 V output with a 7 to 1 ratio the reflected term is 170 V, the spike 150 V with a clamp, and the sum with a 680 V bus is 1000 V. That is above this part, which is why a 900 V auxiliary supply on a 680 V bus usually runs a two switch forward or a flyback with an active clamp rather than a plain flyback.

A two switch forward is the cleaner answer. Two switches in series see the bus, each one sees half of it plus the diode drop, so a 680 V bus puts 340 V on each part and a 900 V rating gives a margin of 2.6. The part then carries the full primary current at 1 to 4 A and the resistance matters very little. This is the application where the 20 A, 270 milliohm part is the natural pick, and a smaller die with 900 V would be better still if one existed.

The third option is a depletion mode start up path or a linear pre regulator, where the part is on for a few milliseconds at a time and the loss is a pulse rather than a continuous figure. Those circuits run at 10 to 50 mA and the 20 A rating is irrelevant; the voltage and the package are the only things that matter.

Losses and the thermal picture

At 270 milliohm the die makes 0.27 W at 1 A, 1.1 W at 2 A, 2.4 W at 3 A and 17.3 W at 8 A. On a hot die the resistance roughly doubles, so the 3 A figure is 4.8 W at 125 C and the 8 A figure 35 W.

At 2 to 3 A the part needs no heatsink at all. A TO3P tab soldered to 4 square centimetres of copper on the board has a junction to ambient resistance of 30 to 45 K per watt, and 2.4 W in that path is 70 to 110 K of rise, which is too much on a 40 C internal ambient. A small clip on sink of 10 K per watt brings it to 24 to 40 K and the part is then comfortable at 3 A. This is the reason the TO3P body is used rather than a smaller one: the tab is the heatsink.

The switching loss is where a 900 V superjunction part differs from a 1200 V planar part. The output charge is small for the voltage, so at 100 kHz and 3 A the crossover is 2 to 3 W, which is comparable to the conduction loss. At 300 kHz it becomes the dominant term and the part is no longer the right choice.

Where it is used, and how it is held in stock

Gate driver bias supplies in 480 V drives, the housekeeping supply in a solar string inverter, the control supply in a high voltage battery charger, and the start up path in a 700 V DC link are the four places this part appears. In each case the current is below 5 A and the voltage is above 600 V, which is the narrow window where a small 900 V die is the cheapest answer.

This is a part that often sits on a board for a decade. The auxiliary supply does not change when the main stage is re-rated, so the code stays on the bill of materials while the platform lives through three or four revisions. That makes the supply position, rather than the price, the thing to manage. The safety stock planning page covers how much of a long life code is held against a build plan, and the component lead time solutions page covers how a long lead item is planned rather than discovered at the line.

The sourcing side of this part is covered on the safety stock planning. For a long life auxiliary supply code, that page covers how much is held against the build plan.

Questions we get on this code

Can it run a 20 W flyback from a 680 V bus? Only with an active clamp or a two switch topology. A plain flyback with a 7 to 1 ratio puts 1000 V across the switch on a 680 V bus, and this part is rated at 900 V.

Does 270 milliohm limit the current? No. At 3 A the loss is 2.4 W, which is well inside the package. The current limit is the thermal path on the tab, not the die.

Is the part avalanche rated for a leakage spike? The vendor table gives the voltage and the resistance only, so the spike has to be clamped and measured rather than absorbed. A TVS across the switch plus a snubber on the primary is the standard answer.

Can it be used as a linear pass element? Yes, and the SOA matters more than the resistance there. A 680 V bus with a 20 mA load in a linear pre regulator is 13 W in the die, which the TO3P tab can pass only with a sink.