Contact Us

VBP19R20S

Brand: VBsemi
VBsemi VBP19R20S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP19R20S — Discrete & Power Semiconductors | Superb Automation

VBP19R20S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP19R20S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP19R20S: 900 V and 20 A in a TO247 with 205 milliohm

The VBP19R20S is a single N channel MOSFET in a TO247 body, rated at 900 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of drain current and 205 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die. It is the larger of the two 900 V parts in this band and the one used as a main switch on a 480 V drive at 1.5 to 2.2 kW.

At 205 milliohm the die is nearly twice the area of the 370 milliohm member, and it carries twice the current at the same loss. At 20 A it makes 82 W, at 15 A 46 W, at 10 A 21 W and at 5 A 5 W. On a fan cooled heatsink the working current is 9 to 12 A, and on a plate heatsink 6 to 8 A.

The class is chosen for margin rather than for efficiency. A 900 V part at 205 milliohm has three times the resistance of a 600 V part at 70 milliohm, and the same current costs three times the loss. What it buys is the ability to run on a 480 V line with a braking load without a surge failure.

Key data for the VBP19R20S

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS900 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID20 A
RDS(on) at 10 V205 milliohm
StructureSuperjunction, multiple epitaxy
Loss at 5 A5.1 W
Loss at 10 A20.5 W
Loss at 15 A46.1 W
Loss at 20 A82.0 W

The margin arithmetic on a 480 V line

The bus is 680 V. A braking motor at 20 percent regeneration puts it at 750 V, and a varistor clamp at 850 V holds a surge. A 900 V part has 50 V above the clamp, which is thin but positive. A 1200 V part has 350 V and costs twice the resistance.

That 50 V is why the clamp has to be checked as part of the drive rather than assumed. A varistor with a 10 percent tolerance and a 15 percent rise at surge current can clamp at 900 V, which puts the part at its rating with no margin at all.

The usual arrangement is a clamp at 800 V nominal, a 900 V switch, and a brake chopper that fires at 760 V. The brake chopper is what keeps the bus inside the clamp, and the clamp is what protects the switch if the chopper fails.

Loss at 8 A on a plate heatsink

At 8 A and 205 milliohm the loss is 13 W cold and 24 W hot. A TO247 on a 1.5 K per watt plate heatsink at 40 C ambient sits at 93 C junction, which is a working point with margin. At 12 A the hot loss is 53 W and the junction is at 157 C, which is outside.

So the honest continuous current on a plate is 8 to 9 A, and the printed 20 A is a die rating at a 25 C case. On a fan cooled heatsink at 0.5 K per watt the ceiling is 12 to 13 A.

Switching at 680 V and 8 A with a 40 ns crossover is 5 W peak, and averaged at 8 kHz it is 1 W. The drive case is conduction dominated, and the resistance is the number that sets the thermal path.

Where this part fits

480 V drives with braking loads at 1.5 to 2.2 kW, auxiliary supplies on a 680 V bus, high voltage battery chargers, and power supplies for 700 V solar strings. In a drive the part runs at 4 to 8 kHz and the body diode carries the motor current during the dead time.

In a charger the part runs at 40 to 100 kHz and the capacitance loss becomes a real term. At 100 kHz and 680 V the stored energy in the output capacitance is 10 to 20 W, which is more than the conduction loss at 8 A.

For a 690 V line the class is 1200 V. Where a family spans 480 V and 690 V, the 1200 V part is the common code and the 900 V part is the cost down for the 480 V variant. The OEM procurement page covers how the two codes are held on one contract without a substitution at the line.

The gate threshold of 3.5 V leaves a narrow window for a negative spike on the source. In a drive at 680 V the source inductance of a 20 mm return is 15 nH, and a 20 A turn off at 20 A per ns produces a 300 V spike across it, of which a fraction appears between gate and source. A 10 k pull down resistor and a tight source return keep that spike under a volt. A shared source trace with the power stage can push it past the threshold and turn the part on for a few hundred nanoseconds, which reads as a random overcurrent trip.

The sourcing side of this part is covered on the purchase order follow up. For a main switch on a long build, that page covers how the order is followed from release to delivery.

Questions we get on this code

Is 900 V enough with a varistor at 850 V? That leaves 50 V, which is not a margin. The clamp should be set at 800 V nominal so the part has 100 V at the clamp.

What is the difference from the 15 A part? The 15 A part prints 370 milliohm and the 20 A part 205 milliohm. The second is a larger die at nearly half the resistance, so it is not a graded version of the first.

Can it be used on a 690 V line? No. That bus is 975 V and the part is over its rating before any surge.

What is the hot resistance? About 1.8 times the printed figure, so 370 milliohm at 125 C. That is the number for any thermal calculation.