Contact Us

VBP18R25SFD

Brand: VBsemi
VBsemi VBP18R25SFD is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP18R25SFD — Discrete & Power Semiconductors | Superb Automation

VBP18R25SFD

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP18R25SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP18R25SFD: 800 V and 25 A in a TO247 with 140 milliohm

The VBP18R25SFD is a single N channel MOSFET in a TO247 body, rated at 800 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 25 A of drain current and 140 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die with an FD fast recovery body diode grade. It is the diode graded member of the 800 V family at this current.

The FD suffix is the point of the part. In a half bridge the body diode of each switch conducts the load current during the dead time, and then recovers when the opposite switch turns on. A standard superjunction body diode recovers slowly, and the recovered charge adds to the turn on loss of the opposite die. At 680 V and 10 A that recovered charge can be 100 to 200 nC, which is 7 to 14 mJ per cycle at the bus voltage, or 3 to 6 W at 40 kHz.

At 140 milliohm and 25 A the die makes 88 W, at 19 A 51 W, at 12 A 20 W and at 6 A 5 W. The thermal working point is 11 to 14 A on a plate heatsink and 15 A with a fan.

Key data for the VBP18R25SFD

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS800 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID25 A
RDS(on) at 10 V140 milliohm
StructureSuperjunction, multiple epitaxy
Diode gradeFD, fast recovery body diode
Loss at 6 A5.0 W
Loss at 12 A20.2 W
Loss at 19 A50.5 W
Loss at 25 A87.5 W

Dead time loss in a drive bridge

In a six switch drive at 8 kHz the dead time is 1 to 2 microseconds to avoid shoot through. During that interval the body diode conducts the motor current, which is 9 A at 2 kW on a 565 V bus. A body diode at 1.3 V forward makes 12 W during the dead time, and at 1.5 microseconds in a 125 microsecond period that is 0.14 W averaged.

The recovery is the larger term. When the opposite switch turns on, the body diode of the conducting switch has to recover, and the recovered charge flows through both devices. At 9 A and 680 V with 150 nC of recovered charge the energy per event is 0.1 mJ, which at 8 kHz is 0.8 W spread across the bridge.

At 40 kHz the same recovery is 4 W and becomes visible on the heatsink. That is where the FD grade pays for itself, and below 10 kHz it is a marginal purchase.

What the 800 V class costs and buys

An 800 V die at 140 milliohm is larger than a 600 V die at the same resistance, because the drift region is longer. The area penalty is 30 to 40 percent, which shows in the price. What it buys is margin: on a 480 V line the bus is 680 V and the 600 V class is not usable at all.

On a 400 V line the 600 V class is usable with 235 V of margin at the bus, and the 800 V class doubles that margin for a price premium. Where the surge test is severe, the premium is worth it, and where the line is clean, the 600 V part is the cheaper working answer.

On a 690 V line neither class works and the answer is 1200 V. The 800 V class is therefore tied to 400 V and 480 V lines, and the current range of 10 to 20 A is the 1 to 3 kW drive window.

Where this part fits

400 V and 480 V motor drives at 1.5 to 3 kW, servo drives at 400 V, uninterrupted power stages, and the primary of an auxiliary supply on a 680 V bus. In a servo drive the switching frequency is 8 to 16 kHz and the dead time loss is small, so the diode grade matters less than the resistance.

In a power factor stage the body diode never conducts and the FD grade is wasted. The standard part is the right purchase there.

Where a board is moving from a 600 V driver stage to an 800 V one, the gate drive does not change, but the dead time does, because the higher bus slows the body diode recovery. The how to verify a drop in replacement page covers the measurements that have to be repeated when the voltage class changes.

The dead time is set by the driver and the gate resistor, not by the part. At 800 V the turn off delay of this die with a 10 ohm resistor is 120 to 180 ns, and the driver has to hold the opposite gate off for longer than that plus the tolerance. A 1 microsecond dead time is safe and costs 0.8 percent of the period at 8 kHz. Reducing it to 300 ns saves 0.5 percent of the loss and removes the margin that keeps the bridge from a shoot through at a hot corner.

The sourcing side of this part is covered on the supplier scorecard. For a diode graded part in a drive bridge, that page covers how the source is scored over time.

Questions we get on this code

Is the extra 2 milliohm against the standard part real? The difference is inside the grading window and not meaningful. The diode grade is the reason to choose this part.

Does it help in a boost stage? No. The body diode does not conduct, so the standard part is equivalent and cheaper.

Can the dead time be reduced to cut the diode loss? To a point. Below 500 ns the shoot through risk rises with the gate drive tolerance and the temperature drift of the turn off time, and the saving is under a watt.

What is the hot resistance? About 1.8 times the printed figure, so 250 milliohm at 125 C. Size the heatsink on that number.