VBP18R20SFD
Product Specifications
VBP18R20SFD
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP18R20SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP18R20SFD: 800 V and 20 A in a TO247 with 205 milliohm
The VBP18R20SFD is a single N channel MOSFET in a TO247 body, rated at 800 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of drain current and 205 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die with an FD fast recovery body diode grade.
Eight hundred volts is the class for a 480 V three phase line, which rectifies to 680 V. The margin is 120 V, or 18 percent, which covers a clamped surge but not a hard braking motor. It is the most common class in 480 V drives at 1 to 3 kW because it is cheaper per milliohm than the 900 V class.
At 205 milliohm and 20 A the die makes 82 W, at 15 A 46 W, at 10 A 21 W and at 5 A 5 W. On a plate heatsink the working current is 6 to 8 A, and on a fan cooled heatsink 10 to 13 A. This is a mid power switch rather than a main switch at full load.
Key data for the VBP18R20SFD
| Configuration | Single N channel |
| Package | TO247, through hole, tab on the drain |
| VDS | 800 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 20 A |
| RDS(on) at 10 V | 205 milliohm |
| Structure | Superjunction, multiple epitaxy |
| Diode grade | FD, fast recovery body diode |
| Loss at 5 A | 5.1 W |
| Loss at 10 A | 20.5 W |
| Loss at 20 A | 82.0 W |
The 800 V class on a 480 V line
A 480 V three phase rectifier gives 680 V DC. A 800 V part at that bus runs at 0.85 of rating, which is high for a switching device. A 10 percent line rise takes the bus to 750 V, and a lightning surge clamped at 900 V puts the part over its rating.
That is why a drive on a 480 V line uses an 800 V part only where the surge clamp is set below 750 V and the motor does not regenerate hard. Where the load is a crane or a press that brakes into the drive, the bus rises and the class is 900 V or 1200 V.
On a 400 V line the rectified bus is 565 V and an 800 V part has 235 V of margin, which is comfortable. That is the same part used with a wider margin, and the price is the same. Buyers on 400 V lines often buy this class for the margin rather than the voltage.
Thermal chain at 10 A
At 10 A and 205 milliohm the loss is 21 W cold and 37 W hot. A TO247 with a pad on a 1.5 K per watt plate heatsink at 40 C ambient sits at 40 plus 37 times 2.2, which is 121 C junction. That is inside the limit and close enough that a hot day matters.
At 8 A the hot loss is 24 W and the junction is at 93 C, which is a comfortable working point. At 12 A the hot loss is 54 W and the junction is at 159 C, which is outside. The window between 8 A and 12 A is narrow, and the heatsink decides where inside it the board runs.
The FD diode grade is only relevant in a bridge. In a single ended flyback or a boost stage the body diode never conducts and the grade is paid for without being used.
Where this part fits
480 V and 400 V three phase drives at 1 to 2 kW, auxiliary supplies in drives and inverters, active clamps in flyback stages at 600 V bus, and power supplies for 600 V solar strings at low current. It also appears in the startup path of a high voltage supply, where the switch is in series for a few milliseconds.
In a drive the part runs at 4 to 16 kHz in a half bridge, and the body diode carries the motor current during the dead time. That is where the FD grade matters, because the recovery of a standard body diode at 680 V and 8 A is a spike on the opposite switch.
For a 690 V line the class is 1200 V, and this part is not usable. Where a board has to run on both 400 V and 480 V lines, the 800 V class covers both and the 900 V class costs more for margin that one of the two lines does not need.
Where a drive has to survive a load dump, the 800 V part is protected by the clamp rather than by its own rating. A varistor at 800 V nominal with a 10 percent tolerance clamps at 880 V at rated current, which is above the 800 V rating and inside a 900 V one. That is the arithmetic that decides the class on a 480 V line with a mechanical load, and it is settled by the clamp datasheet rather than by the motor. The BOM scrubbing page covers how that check is run across a whole drive family.
The sourcing side of this part is covered on the incoming inspection plan. For an 800 V diode graded part, that page covers what is measured on each lot before release.
Questions we get on this code
Is 800 V enough for a 480 V line with a brake? Only if the bus does not rise. A braking motor takes the bus to 750 V and above, so a 900 V class is the safe choice there.
What is the hot resistance? About 1.8 times the printed value, so 370 milliohm at 125 C. A thermal calculation at 205 milliohm is optimistic by a factor of two.
Does the FD grade show in a boost stage? No. The body diode never conducts, so the standard grade is equivalent and cheaper.
Can two of these run in parallel for 16 A? Yes, with separate gate resistors and a symmetric source bus. At 205 milliohm the positive temperature coefficient is enough to hold the split within 15 percent.