Contact Us

VBP165R70SFD

Brand: VBsemi
VBsemi VBP165R70SFD is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP165R70SFD — Discrete & Power Semiconductors | Superb Automation

VBP165R70SFD

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP165R70SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP165R70SFD: 650 V and 70 A in a TO247 with 28 milliohm

The VBP165R70SFD is a single N channel MOSFET in a TO247 body, rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 70 A of drain current and 28 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die. It is the largest member of the 650 V family in this catalogue and the one that carries the main current of a 3 kW stage.

Twenty eight milliohm at 650 V is a big die. The area needed for that resistance at that voltage is roughly the full usable area of a TO247, which is why the family stops here and the next step up is two parts in parallel rather than a larger body. The thermal path is the limit, not the silicon.

The FD suffix marks a fast recovery body diode. On a part intended for a hard switched bridge that matters, because at 70 A the recovered charge of a standard superjunction body diode is large enough to put a visible spike on the opposite switch.

Key data for the VBP165R70SFD

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID70 A
RDS(on) at 10 V28 milliohm
StructureSuperjunction, multiple epitaxy
Diode gradeFD, fast recovery body diode
Loss at 18 A9.1 W
Loss at 35 A34.3 W
Loss at 70 A137.2 W

Loss at 3 kW and the heatsink it needs

At 3 kW from a 400 V bus the input current is 7.5 A average and 20 A peak. At 28 milliohm the conduction loss at the peak is 11 W and the root mean square over the line cycle is 9.6 A giving 2.6 W. Switching at 400 V and 20 A with a 20 ns crossover is 8 W peak and 3.6 W averaged. Total 6.2 W cold.

Hot, the resistance roughly doubles to 55 milliohm and the conduction term becomes 5 W root mean square, so the total is 8.6 W. A TO247 on a 0.8 K per watt heatsink at 45 C ambient sits at 114 C junction, which is inside the limit with 35 C of margin for a hot day.

At 5 kW the peak is 33 A, the conduction term is 30 W hot, and the switching term is 6 W, so the total is 36 W. That is a fan cooled heatsink and a 2 K per watt forced air path, or two parts in parallel.

Paralleling two of these

Two parts at 28 milliohm in parallel give 14 milliohm shared, but only if the current splits evenly. Superjunction dies have a positive temperature coefficient above a few amps, which helps, and the split is then set by the source connection rather than the die. A symmetric source bus with equal trace length to both sources holds the split within 10 percent.

The gate side is the harder half. Two gates driven from one resistor share the current at turn on and the slower die takes more of the switching loss. Separate gate resistors of 4.7 ohm each, fed from one driver, keep the two transitions within a few nanoseconds of each other.

The body diode recovery doubles when two parts run in parallel, so the opposite switch sees twice the recovered charge. In a hard switched bridge that is the parameter that decides whether paralleling is acceptable at all.

Where this part fits

Power factor stages from 2.5 to 5 kW, solar string inverters at 400 to 500 V, EV chargers with a 400 V link, and the primary of a 3 kW LLC. In a server power supply at 3 kW with a 400 V bus and a 12 V output, this is the primary switch and the secondary is a synchronous rectifier pair.

In a solar inverter the part runs at 16 to 32 kHz and the switching loss is a smaller share, so the conduction term dominates and the low resistance is worth the die cost. In a 100 kHz LLC the switching term dominates and the gate charge becomes the parameter to compare.

Where the stage has to run from a 480 V three phase line, the class is 900 V and this part is not usable. The material requirements planning page covers how the two voltage classes are planned against a build that serves both line voltages.

One more number decides the package. The drain tab is the electrical connection and the thermal pad at the same time, and at 6 W the tab has to be soldered or clamped to copper rather than fed by a trace. A 2 mm wide trace from a TO247 drain to a connector carries 20 A at 1.5 mm per amp, so a 30 A working current needs 4 mm of copper on the top layer or a second layer stitched with 20 vias. Where the copper is thinner, the trace runs hotter than the die and the thermal calculation is wrong before the part is even placed.

The sourcing side of this part is covered on the component obsolescence management. For the largest die in a 650 V family, that page covers how the supply is watched as the family narrows.

Questions we get on this code

Is 70 A a continuous rating? No. At 70 A the die makes 137 W cold and near 270 W hot, which no TO247 can pass to a heatsink. The continuous working current on a fan cooled heatsink is 30 to 40 A.

Can it run without a heatsink? Only at a few amps. At 10 A the loss is 2.8 W cold and 5.5 W hot, which a bare TO247 tab can just about pass to still air at 60 C rise.

Does the FD diode grade matter in a boost stage? No. The body diode never conducts in a boost, so the standard grade is cheaper and equivalent.

What is the gate charge? Not printed on the vendor page. For a 100 kHz stage, ask for the curve, because a large superjunction die of this class is in the 60 to 100 nC region and that sets the driver.