Contact Us

VBP165R36S

Brand: VBsemi
VBsemi VBP165R36S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP165R36S — Discrete & Power Semiconductors | Superb Automation

VBP165R36S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP165R36S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP165R36S: 650 V and 36 A in a TO247 with 75 milliohm

The VBP165R36S is a single N channel MOSFET in a TO247 body, rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 36 A of drain current and 75 milliohm at a 10 V gate. The vendor table lists the die as superjunction multiple epitaxy. The S suffix marks the superjunction family rather than a planar die with a bigger area.

Superjunction at 650 V is what makes 75 milliohm possible in a TO247. A planar die at that voltage needs two to three times the area to reach the same resistance, and the area is the cost. The charge balance structure puts p columns through the drift region so the drift can be doped far above the planar limit, and the on resistance falls by a factor of three to five for the same breakdown voltage.

The price of the structure is a sharper output capacitance curve and a faster body diode. Both matter in a bridge, where the recovered charge of the body diode turns into a current spike through the opposite switch. In a single ended flyback or a boost stage neither shows, which is why the part is most often bought for a power factor stage.

Key data for the VBP165R36S

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID36 A
RDS(on) at 10 V75 milliohm
StructureSuperjunction, multiple epitaxy
Loss at 9 A6.1 W
Loss at 18 A24.3 W
Loss at 27 A54.7 W
Loss at 36 A97.2 W

Why 75 milliohm changes the board

A 1 kW power factor stage at 400 V draws 2.5 A average and 7 A peak from a 230 V line. At 75 milliohm the conduction loss at the peak is 3.7 W and the root mean square over the line cycle is 3.2 A giving 0.8 W. Switching loss at 400 V and 7 A with a 20 ns crossover is 2.8 W peak and 1.2 W averaged. The total is 2 W, which is a TO247 on a small heatsink at 60 C rise.

The same stage with a 280 milliohm planar part is 7 W of conduction and a 90 C rise, which needs a bigger heatsink and a fan. That is the whole argument for superjunction in this class: the heatsink and the fan are more expensive than the difference in die cost.

At 2 kW the current doubles and the loss at 75 milliohm is 8 W conduction, still inside a single TO247 on a proper heatsink. At 3 kW the part is at 12 W and the parallel pair question arrives, and two parts sharing a symmetric source connection are then cheaper than one larger die.

The 650 V rating on a single phase line

Steady state on a 230 V line is a 400 V switch node. The margin to 650 V is 250 V, and a 2 kV surge clamped by a metal oxide varistor at 550 V still leaves 100 V. That is a thinner margin than it looks, because the clamp voltage rises with the surge current and the trace inductance adds a spike on top.

The practical rule is a 20 mm to 25 mm creepage between drain and source on the board, a gate resistor close to the gate, and a snubber or a soft switching cell if the leakage inductance of the loop is above 20 nH. A part at 75 milliohm switches 7 A in 20 ns, which is 350 A per microsecond through the loop, and 20 nH at that rate is a 7 V spike.

Where the same board has to run on a 277 V single phase line, the bus climbs to 480 V and the margin falls to 170 V. That is still inside the class if the surge clamp is set at 600 V, but the part is then at 0.74 of rating in steady state rather than 0.62.

Where this part fits

Power factor correction stages from 500 W to 2 kW, LLC and forward converters at 400 V bus, solar microinverters at 400 V, and battery chargers with a 400 V DC link. In a bridge the body diode recovery has to be checked against the opposite switch, and a part with a fast recovery body diode is the right choice for a hard switched half bridge.

In a soft switched LLC the body diode never sees a hard recovery, so the faster superjunction die is an advantage rather than a risk. At 100 kHz the gate charge sets the driver loss, and this die is in the 30 to 40 nC region, which a 2 A driver handles without a heat spreader.

Where a board uses several power levels of the same topology, the 36 A part at 75 milliohm and the 70 A part at 28 milliohm are often held as a pair. The BOM consolidation page covers how a family is merged to one or two codes without losing thermal margin.

The sourcing side of this part is covered on the strategic sourcing. For a superjunction code used across several power levels, that page covers how the source is held.

Questions we get on this code

Is this the same die as the 36 A FD part? The FD part prints 68 milliohm at the same 36 A and the same voltage, so the two are close enough that the difference is likely a grade of the same structure. They are not documented as the same die, so a swap needs a thermal check rather than an assumption.

Does the part need a snubber? On a hard switched bridge at 100 kHz and 7 A, yes, or a gate resistor tuned to slow the turn on. On a boost stage with a soft recovery diode, often not.

What is the gate charge? The vendor page does not print it. For a driver sizing exercise, ask for the curve with the sample, because 75 milliohm superjunction dies vary by a factor of two between families.

How does it behave at 5 V gate drive? The table prints a 10 V column only. A 5 V drive at 3.5 V threshold leaves little overdrive, so the resistance rises and the switching slows. Drive at 10 V or 12 V and keep the gate loop short.